Plymouth >> Breeze 2.0/2.4L – Neon 2.0L – Prowler 3.5L (1997 – 2000)

Model Year Engine identification System
Breeze 2.0L 1998 ECB   SBEC  II
Breeze 2.4L 1998 EDZ   SBEC  II
Neon 2.0L 1998 ECB/ECC   SBEC  II
Prowler 3.5L 1997-00 VIN  position 8  = G SBEC  II

General information

  • Malfunction indicator lamp (MIL) will illuminate or flash if certain faults are recorded .
  • ECM operates in backup mode if sensors fail , to enable vehicle to be driven to repair shop.

Accessing

• Trouble codes can only be displayed by using a Scan Tool connected to the data link connector (DLC):
  1. o Breeze 1
  2. o Neon 2
  3. o Prowler 3

Erasing

• Trouble codes can only be erased by using a Scan Tool connected to the data link connector (DLC ).

Trouble code  identification

Scan code Ptype Fault location Probable cause
PO,P2,UO Refer to OBO-II trouble code tables
P1195 Heated oxygen sensor (H02S) 1, bank 1 slow response Wiring, heating inoperative, H025
P1196 Heated oxygen sensor (H02S) 1, bank 2 slow response Wiring, heating inoperative, H025
P1281 Engine temperature -low for long period Wiring, cooling system, coolant thermostat, ECT sensor
P1282 Fuel pump relay Wiring open circuit/short circuit, fuel pump relay
P1289 Intake manifold air control solenoid Wiring open circuit/short circuit, intake manifold air control solenoid
P1294 Idle speed control (ISC) system rpm lower/ higher than expected Wiring, air leak, throttle valve tight/sticking, lAC valve
P1297 Mani~old absolute pressure (MAP) l?ensor Wiring, hose connection(s), MAP sensor
P1299 Manifold absolute pressure (MAP) sensor/ throttle position (TP) sensor Intake leak, hose connection(s), MAP sensor, TP sensor
P1388 Engine control relay Wiring open circuit/short circuit, engine control relay
P1389 Engine control relay Wiring open circuit, engine control relay
P1390 Timing belt jumped 1 tooth or more Timing belt loose/jumped position
P1391 Crankshaft position (CKP) sensor/camshaft position (CMP) sensor -intermittent signal Wiring, poor connection, air gap, CKP sensor, CMP sensor
P1398 Engine control module (ECM) -misfire detection limit reached Wiring, poor connection, CKP sensor
P1478 Ambient/battery temperature sensor Wiring, ambient/battery temperature sensor
P1486 Evaporative emission (EVAP) system -blockage detected Hose connection(s), hose blocked/trapped, EVAP canister
P1489 Engine coolant blower motor relay -high speed Wiring open circuit/short circuit, engine coolant blower motor relay -high speed
P1490 Engine coolant blower motor relay -low speed Wiring open circuit/short circuit, engine coolant blower motor relay -low speed
P1491 Engine coolant blower motor relay -low/high speed Wiring open circuit/short circuit, engine coolant blower motor relay -low/high speed
P1492 Ambient/battery temperature sensor -voltage high Wiring, ambient/battery temperature sensor
P1493 Ambient/battery temperature sensor -voltage low Wiring, ambient/battery temperature sensor
P1494 Evaporative emission (EVAP) leak detection pump -pressure switch Wiring, hose leak/blockage, EVAP leak detection pump
P1495 Evaporative emission (EVAP) leak detection pump solenoid Wiring open circuit/short circuit, hose leak/ blockage, EVAP leak detection pump solenoid
P1496 Engine control module (ECM) -5 volt output low ECM
P1594 Alternator -voltage high Wiring, battery, alternator
P1595 Cruise control Wiring open circuit/short circuit, hoses, cruise control master switch, cruise control vacuum switching valve
P1596 Cruise control master switch -high voltage Wiring, cruise control master switch
P1597 Cruise control master switch -low voltage Wiring, cruise control master switch
P1598 AlC refrigerant pressure sensor -high input Wiring, AlC refrigerant pressure too high (coolingfault/incorrectly charged), AlC refrigerant pressure sensor
P1599 AlC refrigerant pressure sensor -low input Wiring, AlC refrigerant pressure too low(incorrectly charged), AlC refrigerant pressure sensor
P1682 Altemator -voltage low Wiring, battery, alternator drive belt, alternator
P1683 Cruise control Wiring, cruise control vacuum switching valve
P1685 Key not programmed into immobilizer control module Wiring, ignition key not matched/damaged,immobilizer control module
P1686 CAN data bus, immobilizer control module -no signal Wiring, immobilizer control module
P1695 CAN data bus, body control module (SCM) no signal Wiring, BCM
P1696 Engine control module (ECM) -EEPROM error ECM
P1697 Engine control module (ECM) -EEPROM error ECM
P1698 CAN data bus, transmission control module(TCM) no signal Wiring, TCM
P1899 Park/neutral position (PNP) switch -input circuit malfunction Wiring, PNP switch, ECMITCM
 
Scan code Hex type Fault location Probable cause
1 Camshaft position (CMP) sensor no signal Wiring, CMP sensor
2 Engine control module (ECM) -intemal fault ECM
5 Alternator -voltage low Wiring, battery, alternator drive belt, alternator
6 Alternator -voltage high Wiring, battery, alternator
OA Engine control relay Wiring open circuit/short circuit, engine control relay
8 Alternator, field control -circuit malfunction Wiring open circuit/short circuit, alternator, battery
OC Torque converter clutch (TCC) solenoid -electrical Wiring open circuit/short circuit, TCC solenoid
OE Engine coolant blower motor relay -low/high speed Wiring open circuit/short circuit, engine coolant blower motor relay -low/high speed
OF Cruise control Wiring open circuit/short circuit, hoses, cruisecontrol master switch, cruise control vacuum switching valve
10 AlC compressor clutch relay Wiring open circuit/short circuit, AlC compressorclutch relay
11 Exhaust gas recirculation (EGR) -circuit malfunction Wiring open circuit/short circuit, EGR solenoid
12 Evaporative emission (EVAP) canister purge valve -circuit malfunction Wiring open circuit/short circuit, EVAP canister purge valve
13 Injector 3 -circuit malfunction Wiring, injector
14 Injector 2 -circuit malfunction Wiring, injector
15 Injector 1 -circuit malfunction Wiring, injector
19 Idle speed control (ISC) system -malfunction Wiring open circuit/short circuit, lAC valve
1A Throttle position (TP) sensor -low input Wiring short circuit to ground, TP sensor
18 Throttle position (TP) sensor -high input Wiring short circuit to positive, TP sensor
1E Engine coolant temperature (ECT) sensor lowinput Wiring short circuit to ground, coolant thermostat,ECT sensor
1F Engine coolant temperature (ECT) sensor high input Wiring open circuit/short circuit to positive, coolant thermostat, ground wire defective, ECTsensor
20 Heated oxygen sensor (H02S) 1, bank 1 no activity detected Wiring open circuit, heating inoperative, H02S
21 Engine temperature -low for long period Wiring, cooling system, coolant thermostat,ECTsensor
23 Vehicle speed sensor (VSS) -signal Wiring, VSS
24 Manifold absolute pressure (MAP) sensor low input Wiring short circuit to ground, MAP sensor
25 Manifold absolute pressure (MAP) sensor high input Wiring short circuit to positive, MAP sensor
27 Manifold absolute pressure (MAP) sensor Wiring, hose connection(s), MAP sensor
28 Crankshaft position (CKP) sensor no signal Wiring, air gap, CKP sensor
29 Ignition coil C, primary/secondary -circuitmalfunction Wiring, ignition coil
2A Ignition coil B, primary/secondary -circuit malfunction Wiring, ignition coil
28 Ignition coil A, primary/secondary -circuit malfunction Wiring, ignition coil
2C Engine control relay Wiring open circuit, engine control relay
2E Exhaust gas recirculation (EGR) system -insufficient flow detected Wiring, hose leak/blockage, EGR valve, EGR solenoid
30 Engine control module (ECM) -EEPROM error ECM
31 Engine control module (ECM) EEPROM error ECM
39 Intake air temperature (IAT) sensor -low input Wiring short circuit to ground, IAT sensor
3A Intake air temperature (IAT) sensor -high input . Wiring open circuit/short circuit to positive, ground wire defective, IAT sensor
38 Knock sensor (KS) 1 -no signal Wiring, KS incorrectly tightened, KS
3C Manifold absolute pressure (MAP) sensor barometric pressure range/ performance problem Intake/exhaust leak, wiring, MAP sensor
3D Injector 4 -circuit malfunction Wiring, injector
3E Heated oxygen sensor (H02S) 1, bank 1 high voltage Wiring short circuit to positive, fuel pressure,injector control, EVAP canister purge valve, air filter blocked, H02S
41 Heated oxygen sensor (H02S) 1, bank 2 no activity detected Wiring, H02S
42 Heated oxygen sensor (H02S) 1, bank 2 high voltage Wiring short circuit to positive, fuel pressure, injector control, EVAP canister purge valve, air filter blocked, H02S
44 Engine control module (ECM) -internal fault ECM
45 Injector 5 -circuit malfunction Wiring, injector
46 Injector 6 -circuit malfunction Wiring, injector
47 Ambientlbattery temperature sensor Wiring, ambient/battery temperature sensor
4C Ignition coil 0 , primary/secondary -circuit malfunction Wiring, ignition coil
40 Ignition coil E, primary/secondary -circuit malfunction Wiring, ignition coil
52 Cruise control Wiring, cruise control vacuum switching valve
56 Cruise control master switch -high voltage Wiring, cruise control master switch
57 Cruise control master switch -low voltage Wiring, cruise control master switch
58 Intake manifold air control solenoid Wiring open circuit/short circuit, intake manifold air control solenoid
5A AlC refrigerant pressure sensor -high input Wiring, AlC refrigerant pressure too high (cooling fault/incorrectly charged), AlC refrigerant pressure sensor
58 AlC refrigerant pressure sensor -low input Wiring, AlC refrigerant pressure too low (incorrectly charged), AlC refrigerant pressure sensor
5C Engine coolant blower motor relay -low speed Wiring open circuit/short circuit, engine coolant blower motor relay -low speed
50 Engine coolant blower motor relay -high speed Wiring open circuit/short circuit, engine coolantblower motor relay -high speed
60 CAN data bus, transmission control module(TCM) -no signal Wiring, TCM
61 CAN data bus, body control module (BCM) nosignal Wiring,8CM
65 Fuel pump relay Wiring open circuit/short circuit, fuel pump relay
66 Heated oxygen sensor (H02S) 1, bank 1 slow response Wiring, heating inoperative, H02S
67 Heated oxygen sensor (H02S) 1, bank 1 heatercontrol -circuit malfunction Wiring, H02S
69 6A Heated oxygen sensor (H02S) 2, bank 1, heater control -circuit malfunction Random/multiple cylinder{s} -misfire detected Wiring, H02S Wiring, spark plug(s), HT lead(s), injector(s), ignition coil(s), low compression
68 Cylinder 1 -misfire detected Wiring, engine mechanical fault, ignition/fuelsystem, injector
6C Cylinder 2 -misfire detected Wiring, engine mechanical fault, ignition/fuel system, injector
60 Cylinder 3 -misfire detected Wiring, engine mechanical fault, ignition/fuel system, injector
6E Cylinder 4 -misfire detected Wiring, engine mechanical fault, ignition/fuel system, injector
70 Catalytic converter system, bank 1 -efficiency below threshold Wiring, heated oxygen sensor (H02S) 2, catalytic converter
71 Evaporative emission (EVAP) system incorrectflow detected Hose connection(s), intake leak, EVAP canister purge valve
72 Park/neutral position (PNP) switch -input circuit malfunction Wiring, PNP switch, ECMITCM
73 Power steering pressure (PSP) switch -range/performance problem Wiring, PS system, PSP switch
76 System too rich Wiring, intake blocked, EVAP canister purge valve, fuel pressure, EGR system, injector(s), air filter blocked, ignition system, heated oxygen sensor (H02S)
77 System too lean Wiring, intake/exhaust leak, MAP sensor, fuel pressure/pump, EVAP canister purge valve, injector(s), heated oxygen sensor (H02S)
78 System too rich, bank 2 Intake blocked, EVAP canister purge valve, fuel pressure, EGR system, injector(s), heated oxygen sensor (H02S)
79 System too lean, bank 2 Intake/exhaust leak, fuel pressure/pump, injector(s), AIR system, hose connection(s)
7A Heated oxygen sensor (H02S) 1, bank 2 slow response Wiring, heating inoperative, H02S
7C Heated oxygen sensor (H02S) 1, bank 2, heater control -circuit malfunction Wiring, H025
70 Heated oxygen sensor (H02S) 2, bank 2, heater control -circuit malfunction Wiring, H02S
7E Heated oxygen sensor (H02S) 2, bank 1 high voltage Wiring short circuit to positive, catalytic converter,H025
7F Heated oxygen sensor (H02S) 2, bank 2 high voltage Wiring short circuit to positive, catalytic converter, H025
80 Insufficient coolant temperature for closed loop fuel control Wiring, cooling system, coolant thermostat, ECTsensor
81 Heated oxygen sensor (H02S) 2, bank 1 no activity detected Wiring, heating inoperative, H02S
82 Heated oxygen sensor (H02S) 2, bank 2 no activity detected Wiring, H025
84 Throttle position (TP) sensor -range/performance problem Wiring, accelerator cable adjustment, TP sensor
85 TIming belt jumped 1 tooth or more Timing belt loose/jumpe~ position
89 Transmission control system -malfunction Wiring, ECMITCM
8A Idle speed control (ISC) system -rpm lower/ higher than expected Wiring, air leak, throttle valve tight/sticking, lAC valve
91 Manifold absolute pressure (MAP) sensorl throttle position (TP) sensor Intake leak, hose connection(s), MAP sensor, TP sensor
92 Engine control module (ECM) -5 volt output low ECM
94 Torque converter clutch (TCC) solenoid -circuit malfunction Wiring, TCC solenoid
95 Fuel level sensor -low input Wiring open circuit, fuel level sensor
96 Fuel level sensor -high input Wiring short circuit to positive, fuel level sensor
97 Fuel level sensor -malfunction Wiring, fuel level sensor
98 Brake pedal position (BPP) switch -circuit malfunction Wiring, BPP switch
99 Ambient/battery temperature sensor -voltage low Wiring, ambient/battery temperature sensor
9A Ambient/battery temperature sensor -voltage high Wiring, ambient/battery temperature sensor
9B Heated oxygen sensor (H02S) 1, bank 1 -lowvoltage Wiring short circuit to ground, exhaust leak, H025
9C Heated oxygen sensor (H02S) 2, bank 1 -lowvoltage Wiring short circuit to ground, exhaust leak, H02S
90 Crankshaft position (CKP) sensor/camshaft position (CMP) sensor -intermittent signal Wiring, poor connection, air gap, CKP sensor, CMP sensor
AO Evaporative emission (EVAP) system -small leak detected Hose connection(s), intake leak, EVAP canister,EVAP canister purge valve
A1 Evaporative emission (EVAP) system -large leak detected Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve
AE Cylinder 5 -misfire detected Wiring, engine mechanical fault, ignition/fuel system, injector
AF Cylinder 6 -misfire detected Wiring, engine mechanical fault, ignitionlfuel system, injector
84 Main catalytic converter, bank 2 -efficiency below threshold Catalytic converter, wiring, H02S 2
85 Heated oxygen sensor (H02S) 1, bank 2 -low voltage Wiring short circuit to ground, exhaust leak, H02S
86 Heated oxygen sensor (H02S) 2, bank 2 -low voltage Wiring short circuit to ground, exhaust leak, H02S
B7 Evaporative emission (EVAP) leak detectionpump solenoid Wiring open circuit/short circuit, hose leak/ blockage, EVAP leak detection pump solenoid
88 Evaporative emission (EVAP) leak detection pump -pressure switch Wiring, hose leak/blockage, EVAP leak detection pump
8A Engine control module (ECM) -misfire detection limit reached Wiring, poor connection, CKP sensor
BB Evaporative emission (EVAP) system -blockage detected Hose connection(s), hose blocked/trapped, EVAP canister
CO Heated oxygen sensor (H02S) 1, bank 1 slow response Wiring, heating inoperative, H02S
C1 Heated oxygen sensor (H02S) 1, bank 2 slow response Wiring, heating inoperative, H02S
4 Exhaust gas recirculation (EGR) valve positionsensor A -low input Wiring short circuit to ground, EGR valve position sensor
5 Exhaust gas recirculation (EGR) valve position sensor A -high input Wiring short circuit to positive, EGR valve position sensor
7 Exhaust gas recirculation (EGR) system -range/performance problem Wiring, hose leak/blockage, EGR valve/ solenoid
8 Ignition coil F, primary/secondary -circuit malfunction Wiring, ignition coil
9 Intake manifold air control solenoid (short runner) Wiring open circuit/short circuit, intake manifold air control solenoid (short runner)
E1 CAN data bus, instrumentation -no signal .Wiring, instrumentation control module(mechanical)
E2 CAN data bus, immobilizer control module no signal Wiring, immobilizer control module
E8 Key not programmed into immobilizer control module Wiring, ignition key not matched/damaged,immobilizer control module