Nissan OBD / OBD2 Codes >> Altima – Frontier – Pathfinder – Rogue – Sentra – Xterra (2002 – 2008)

ModeLYearEngine identificationSystem
Altima 2.5L2002-08QR25DE  ECCS
Altima 3.5L2002-08VQ35DE  ECCS
Frontier 2.5/4.0L2005-08QR25DE/VQ40DE  ECCS
Pathfinder 3.5L2002-04VQ35DE  ECCS
Pathfinder 4.0L2005-08VQ40DE  ECCS
Rogue 2.5L2008QR25DE  ECCS
Sentra 1.8/2.0/2.52002-08QG18DE/MR20DE/QR25DE  ECCS
Xterra 4.0L2005-08VQ40DE  ECCS

General information

  • Self-diagnosis function.
  • Malfunction indicator lamp (MIL) will illuminate if certain faults are recorded.
  • ECM operates in backup mode if sensors fail, to enable vehicle to be driven to workshop.
  • Trouble codes can be displayed by the malfunction indicator lamp (MIL) or by using a Scan Tool connected to the data link connector (DLC):
o Except Frontier/Pathfinder 2005 -+/Xterra 1.
o Frontier/Pathfinder 2005 -+/Xterra 2

NOTE: The use of a Scan Tool is essential to obtain full diagnostic information.

Accessing – Mode 1

  • Switch ignition ON.
  • Check MIL illuminates.
  • Start engine. Allow to idle.
  • If MIL extinguishes, no trouble codes have been recorded.
  • If MIL remains illuminated, access trouble codes.

Accessing – Mode 2

  • Ensure accelerator pedal is fully released.
  • Switch ignition ON. Do NOT start engine.
  • Wait 3 seconds.
  • Within 5 seconds, repeat the following 5 times:
o Fully depress accelerator pedal.
o Fully release accelerator pedal.
  • Wait 7 seconds.
  • Fully depress accelerator pedal.
  • After approximately 10 seconds MIL will start flashing.
  • Fully release accelerator pedal.
  • Self-diagnosis now in Mode 2.
  • Count flashes and compare with trouble code table.
  • Each trouble code consists of four groups of one or more flashes.
  • The first group of flashes indicate the ‘thousands’ of the trouble code [2] [A).
  • The second group of flashes indicate the ‘hundreds’ of the trouble code [2] [B).
  • The third group of flashes indicate the ‘tens’ of the trouble code [2] [C].
  • The fourth group of flashes indicate the ‘units’ of the trouble code [2] [D].
  • Ten flashes in a group indicate ‘0’.
  • A short pause separates each trouble code group [2] [E].
  • A long pause separates each trouble code [2] [F].
  • For example: Trouble code P1130 displayed [2].
  • Switch ignition OFF
  • Self-diagnosis will return to Mode 1.

Erasing

  • Trouble codes can be erased by using a Scan Tool connected to the data link connector (DLC) or as follows:
  • Ensure accelerator pedal is fully released.
  • Switch ignition ON. Do NOT start engine.
  • Wait 3 seconds.
  • Within 5 seconds, repeat the following 5 times:
o Fully depress accelerator pedal.
o Fully release accelerator pedal.
  • Wait 7 seconds.
  • Fully depress accelerator pedal.
  • After approximately 10 seconds MIL will start flashing.
  • Fully release accelerator pedal.
  • Self-diagnosis now in Mode 2.
o Fully depress accelerator pedal for more than 10 seconds.
o Fully release accelerator pedal.
o Trouble code 0000 should be displayed.

Trouble code  identification

Flash codeOBD-11 codeFault locationProbable cause
–PO, P2,   uoRefer to OBD-11 trouble code tables–
11P0011Camshaft variable timing control – bank 1 – performanceWiring, CMP sensor, CKP sensor, camshaft valve timing sensor
21P0021Camshaft variable timing control – bank 2 – performanceWiring, CMP sensor, CKP sensor, camshaft variable valve timing sensor
31P0031Heated oxygen sensor (H02S) 1 bank 1 – heater voltage lowWiring, oxygen sensor heater, ECM
32P0032Heated oxygen sensor (H02S) 1 bank 1 – heater voltage highWiring, oxygen sensor heater, ECM
37P0037Heated oxygen sensor (H02S) 2 bank 1 – heater voltage lowWiring, oxygen sensor heater, ECM
38P0038Heated oxygen sensor (H02S) 2 bank 1 – heater voltage highWiring, oxygen sensor heater, ECM
51P0051Heated oxygen sensor (H02S) 1 bank 2- heater voltage lowWiring, oxygen sensor heater, ECM
52P0052Heated oxygen sensor (H02S) 1 bank 2 – heater voltage highWiring, oxygen sensor heater, ECM
57P0057Heated oxygen sensor (H02S) 2 bank 2 – heater voltage lowWiring, oxygen sensor heater, ECM
58P0058Heated oxygen sensor (H02S) 2 bank 2- heater voltage highWiring, oxygen sensor heater, ECM
101P0101Mass air flow (MAF) sensor – range/   performance problemWiring, MAF sensor, air leak, ECM
102P0102Mass air flow (MAF) sensor – voltage lowWiring, MAF sensor, air leak, ECM
103P0103Mass air flow (MAF) sensor – voltage highWiring, MAF sensor, ECM
107P0107Manifold absolute pressure (MAP) sensor – voltage lowWiring, MAP sensor, ECM
108P0108Manifold absolute pressure (MAP) sensor- voltage highWiring, MAP sensor, ECM
112P0112Intake air temperature (IAT) sensor – voltage lowWiring, IAT sensor, ECM
113P0113Intake air temperature (IAT) sensor- voltage highWiring, IAT sensor, ECM
117P0117Engine coolant temperature (ECT)   sensor – voltage lowWiring, ECT sensor, ECM
118P0118Engine coolant temperature (ECT)   sensor – voltage highWiring, ECT sensor, ECM
121P0121Throttle position (TP) sensor – range/performance problemWiring, TP sensor, ECM
122P0122Throttle position (TP) sensor- voltage lowWiring, TP sensor, ECM
123P0123Throttle position (TP) sensor- voltage highWiring, TP sensor, ECM
125P0125Engine coolant temperature – too low for closed loop controlWiring, ECT sensor, cooling system, ECM
127P0127Intake air temperature (IAT) sensor- temperature too highWiring short circuit, IAT sensor, ECM
128P0128Engine coolant temperature – temperature too lowThermostat, ECT sensor, cooling system, ECM
132P0132Heated oxygen sensor (H02S) 1, bank 1 – voltage highWiring, H02S, fuel system, injector, ECM
133P0133Heated oxygen sensor (H02S) 1, bank 1 – slow responseWiring, H025, fuel/intake system, injector, exhaust system, MAF sensor, ECM
134P0134Heated oxygen sensor (H02S) 1, bank 1 – excessively high voltageWiring, H02S, ECM
138P0138Heated oxygen sensor (H02S) 2, bank 1 – voltage highWiring, H025, fuel/intake system, injector, ECM
139P0139Heated oxygen sensor (H02S) 2, bank 1 – circuit malfunctionWiring, H025, intake/fuel system, injector, ECM
152P0152Heated oxygen sensor (H02S) 1, bank 2 – voltage highWiring, H02S, fuel system, injector, ECM
153P0153Heated oxygen sensor (H02S) 1, bank 2 – slow responseWiring, H02S, fuel/intake system, injector, exhaust system, crankcase vent valve, MAF sensor, ECM
154P0154Heated oxygen sensor (H02S) 1, bank 2 – excessively high voltageWiring, H02S, ECM
158P0158Heated oxygen sensor (H02S) 2, bank 2 – voltage highWiring, H02S, fuel/intake system, injector, ECM
159P0159Heated oxygen sensor (H02S) 2, bank 2 – circuit malfunctionWiring, H025, intake/fuel system, injector, ECM
171P0171Fuel trim – bank 1 – mixture too leanWiring, exhaust system, H02Sfront, fuel system, injector, MAF sensor, ECM
172P0172Fuel trim – bank 1 – mixture too richWiring, intake/exhaust system, H02S front, fuel system, injector, MAF sensor, ECM
174P0174Fuel trim – bank 2 – mixture too leanWiring, exhaust system, H025front, fuel system, injector, MAF sensor, ECM
175P0175Fuel trim – bank 2 – mixture too richWiring, exhaust system, H02Sfront, fuel system, injector, MAF sensor, ECM
181P0181Fuel tank temperature sensor- range/performanceWiring, fuel tank temperature sensor, ECM
182P0182Fuel tank temperature sensor – voltage lowWiring, fuel tank temperature sensor, ECM
183P0183Fuel tank temperature sensor – voltage highWiring, fuel tank temperature sensor, ECM
217P0217Engine coolant over temperature conditionWiring, coolant fan, coolant hoses, thermostat, radiator, coolant temperature switch
221P0221Throttle position (TP) sensor 1 & 2 – range/performance problemWiring, TP sensor, ECM
222P0222Throttle position (TP) sensor 1 – voltage lowWiring, TP sensor, ECM
223P0223Throttle position (TP) sensor 1 – voltage highWiring, TP sensor, ECM
226P0226Accelerator pedal position (APP)   sensor 1/2- range/performance problemWiring, APP sensor, ECM
227P0227Accelerator pedal position (APP)   sensor 1 – voltage lowWiring, APP sensor, ECM
228P0228Accelerator pedal position (APP)   sensor 1 – voltage highWiring, APP sensor, ECM
245P0245Supercharger (SC) bypass solenoid valve – malfunctionWiring, SC bypass valve, hose leak/blockage
300P0300Random misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
301P0301Cylinder No.1 – misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
302P0302Cylinder No.2 – misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
303POJOJCylinder No.3 – misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
304P0304Cylinder No.4 – misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
305POJ05Cylinder No.5 – misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
306P0306Cylinder No.6 – misfireWiring, mechanical fault, fuel system, EGR valve, injector, intake/ignition system, CKP sensor, H02S front, ECM
327POJ27Knock sensor (KS) – voltage lowWiring, KS, ECM
328POJ28Knock sensor (KS) – voltage highWiring, KS, ECM
335P0335Crankshaft position (CKP) sensor 1 – circuit malfunctionWiring, CKP sensor, ECM
340P0340Camshaft position (CMP) sensor – circuit malfunctionWiring, CMP sensor, starter motor, ECM
400P0400Exhaust gas recirculation (EGR) system – flow excessively high or lowWiring, hose leak/blockage, EGR valve, EGR/EVAP valve, ECM
402P0402Exhaust gas recirculation (EGR) system – valve malfunctionWiring, EGR valve, EGR back pressure transducer, hose leak/blockage, CMP sensor, MAF sensor, EGRIEVAP valve, ECM
405P0405Exhaust gas recirculation temperature   (EGRT) sensor- low voltageWiring, EGRT sensor, ECM
406P0406Exhaust gas recirculation temperature   (EGRT) sensor- high voltageWiring, EGRT sensor, ECM
420P0420Catalytic converter – bank 1 – efficiency below limitCatalytic converter, wiring, intake/exhaust system, injector, ECM
430P0430Catalytic converter – bank 2 – efficiency below limitCatalytic converter, wiring, intake/exhaust system, injector, ECM
441P0441Evaporative emission (EVAP) canister purge system – flow malfunctionWiring, EVAP valve, hose leak/blockage, canister, BARO sensor, MAP/BARO switching valve, ECM
442P0442Evaporative emission (EVAP) canister purge system – small leakWiring, fuel tank/cap, hose leak/ blockage, EVAP valve/canister, EVAP vent valve, BARO sensor, MAP/BARO switching valve, ECM
444P0444Evaporative emission (EVAP) canister purge system – control valve malfunctionWiring, EVAP control valve, EVAP valve/pressure sensor, hose leak/blockage, ECM
445P0445Evaporative emission (EVAP) canister purge system – control valve malfunctionWiring, EVAP control valve, EVAP valve/pressure sensor, hose leak/blockage, ECM
447P0447Evaporative emission (EVAP) canister purge system – vent control valve malfunctionWiring, EVAP vent control valve, EVAP breather valve/pressure sensor, hose leak/blockage, ECM
452P0452Evaporative emission (EVAP) canister purge system – pressure sensor malfunctionWiring, EVAP pressure sensor, hose leak/blockage, EVAP vent/control valve, EVAP canister, ECM
453P0453Evaporative emission (EVAP) canister purge system – pressure sensor malfunctionWiring, EVAP pressure sensor, hose leak/blockage, EVAP vent/control valve, EVAP canister, ECM
455P0455Evaporative emission (EVAP) canister purge system – gross leakWiring, fuel tank/cap, hose leak/blockage, EVAP valve/canister, EVAP vent valve, BARO sensor, MAP/BARO switching valve, ECM
456P0456Evaporative emission (EVAP) canister purge system – very small leakWiring, fuel tank/cap, hose leak/blockage, EVAP valve/canister, EVAP vent valve, BARO sensor, MAP/BARO switching valve, ECM
460P0460Fuel tank level sensor- signal malfunctionWiring open/short circuit, fuel tank level sensor
461P0461Fuel tank level sensor- range/   performance problemWiring, fuel tank level sensor
462P0462Fuel tank level sensor – voltage lowWiring, fuel tank level sensor
463P0463Fuel tank level sensor – voltage highWiring, fuel tank level sensor
500P0500Vehicle speed sensor (VSS) – circuit malfunctionWiring, VSS, ECM
505P0505Idle speed control system – malfunctionWiring, ISC system, ECM
506P0506Idle speed control system – RPM too lowWiring, ISC system, ECM
507P0507Idle speed control system – RPM too highWiring, ISC system, ECM
510P0510Closed throttle position (CTP) switch – circuit malfunctionWiring, CTP switch, ECM
550P0550Power steering pressure (PSP) sensor- circuit malfunctionWiring, PSP sensor, ECM
600P0600ECM/TCM – communication malfunctionWiring, ECM, TCM
605P0605Engine control module (ECM) – malfunctionECM
650P0650Malfunction indicator lamp (MIL) – circuit malfunctionWiring, ECM
705P0705Park/neutral position (PNP) switch – circuit malfunctionWiring, PNP switch, ECM
710P0710Transmission fluid temperature (TFT)   sensor – excessively high or low voltageWiring, temperature sensor, TCM, ECM
720P0720AT- vehicle speed sensor (VSS)Wiring, VSS, TCM
725P0725Engine speed (RPM) – incorrect voltage signal ECM to TCMWiring, RPM sensor, TCM, ECM
731P0731AT- first gear selection – malfunctionValve block
732P0732AT – second gear selection – malfunctionValve block
733P0733AT – third gear selection -malfunctionValve block
734P0734AT – fourth gear selection – malfunctionValve block
740P0740Torque converter clutch (TCC) solenoid – voltage lowWiring, TCC solenoid, TCM
744P0744Torque converter clutch (TCC) lock-up solenoid – circuit malfunctionWiring, TCC lock-up solenoid, TCM
745P0745AT – line pressure solenoid- voltage lowWiring, line pressure solenoid, TCM
750P0750AT – shift solenoid A- voltage lowWiring, shift solenoid, TCM
755P0755AT – shift solenoid 8 – voltage lowWiring, shift solenoid, TCM
1000U1000CAN communication line – signal malfunctionWiring
1001U1001CAN communication line – signal malfunctionWiring
1010U1010CAN communication line – initialization malfunctionECM
1065P1065Engine control module (ECM) – battery voltage supplyWiring, fuse, ECM
1031P1031Heated oxygen sensor (H02S), bank 1, heater – voltage lowWiring, H02S
1032P1032Heated oxygen sensor (H02S), bank 1, heater – voltage highWiring, H02S
1051P1051Heated oxygen sensor (H02S), bank 2, heater – voltage lowWiring, H02S
1052P1052Heated oxygen sensor (H02S), bank 2, heater – voltage highWiring, H02S
1065P1065Engine control module (ECM) – battery voltage supplyWiring, fuse, ECM
1078P1078Exhaust valve timing control position sensor, bank 1 – circuit malfunctionWiring, exhaust valve timing control position sensor, ECM
1084P1084Exhaust valve timing control position sensor, bank 2 – circuit malfunctionWiring, exhaust valve timing control position sensor, ECM
1102P1102Mass air flow (MAF) sensor – range/performance problemWiring, MAF sensor, air leak, ECM
1110P1110Camshaft position (CMP) actuator – bank 1 – circuit malfunctionWiring, CMP actuator, ECM
1111P1111Camshaft position (CMP) actuator – bank 1 – malfunctionWiring, CMP actuator, ECM
1119P1119Engine coolant temperature (ECT)   sensor – circuit malfunctionWiring, engine coolant temperature   (ECT) sensor
1121P1121Throttle valve position motor – malfunctionThrottle valve position motor
1122P1122Throttle valve position motor – range/performance problemWiring, throttle valve position motor
1124P1124Throttle valve position motor relay – short circuitWiring, throttle valve position motor relay
1126P1126Throttle valve position motor relay – open circuitWiring, throttle valve position motor relay
1128P1128Throttle valve position motor – short circuitWiring, throttle valve position motor
1130P1130Intake manifold air control solenoid – malfunctionWiring, intake manifold air control solenoid, ECM
1131P1131Intake manifold air control solenoid – malfunctionWiring, intake manifold air control solenoid, ECM
1132P1132Intake manifold air control solenoid – circuit malfunctionWiring, intake manifold air control solenoid, ECM
1135P1135Camshaft position (CMP) actuator- bank 1 – circuit malfunctionWiring, CMP actuator, ECM
1136P1136Camshaft position (CMP) actuator – bank 2 – malfunctionWiring, CMP actuator, ECM
1137P1137Intake manifold air control actuator position sensor – circuit malfunctionWiring, intake manifold air control actuator position sensor, ECM
1138P1138Intake manifold air control solenoid – circuit malfunctionWiring, intake manifold air control solenoid, intake manifold air control actuator position sensor, ECM
1140P1140Camshaft variable valve timing sensor – bank 1 – range/performance problemWiring, camshaft variable valve timing sensor, ECM
1143P1143Heated oxygen sensor (H02S) 1, bank 1 – lean shift monitoringWiring, H02S, fuel system, injector, air leak, ECM
1144P1144Heated oxygen sensor (H02S) 1, bank 1 – rich shift monitoringWiring, H02S, fuel system, injector, ECM
1145P1145Camshaft variable valve timing sensor – bank 2 – range/performance problemWiring, camshaft variable valve timing sensor, ECM
1146P1146Heated oxygen sensor (H02S) 2, bank 1 – minimum voltage monitoringWiring, H025, fuel system, injector, ECM
1147P1147Heated oxygen sensor (H02S) 2, bank 1 – maximum voltage monitoringWiring, H02S, fuel system, injector, ECM
1148P1148Closed loop control – bank 1 – inoperativeWiring, H02S front, ECM
1163P1163Heated oxygen sensor (H02S) 1, bank 2 – lean shift monitoringWiring, H02S, fuel system, injector, air leak, ECM
1164P1164Heated oxygen sensor (H02S) 1, bank 2 – rich shift monitoringWiring, H025, fuel system, injector, ECM
1165P1165Intake manifold air control vacuum check switch – malfunctionWiring, intake manifold air control solenoid, intake manifold air control vacuum check switch, ECM
1166P1166Heated oxygen sensor (H02S) 2, bank 2 – minimum voltage monitoringWiring, H02S, fuel system, injector, ECM
1167P1167Heated oxygen sensor (H02S) 2, bank 2 – maximum voltage monitoringWiring, H02S, fuel system, injector, ECM
1168P1168Closed loop control – bank 2 – inoperativeWiring, H02S front, ECM
1211P1211ABS control module – malfunctionWiring, ABS control module
1212P1212ABS control module/traction control module – communication failureWiring, CAN data bus, ABS control module
1217P1217Engine coolant over temperature conditionWiring, coolant fan, coolant hoses, thermostat, radiator, coolant temperature switch
1220P1220Fuel pump control module – circuit malfunctionWiring, fuel pump speed resistor, fuel pump control module
1223P1223Throttle position (TP) sensor 2 – voltage lowWiring, TP sensor, ECM
1224P1224Throttle position (TP) sensor 2 – voltage highWiring, TP sensor, ECM
1225P1225Closed throttle position, learning – voltage too lowThrottle valve position motor, TP sensor 1 & 2
1226P1226Closed throttle position, learning – unsuccessfulThrottle valve position motor, TP sensor 1 & 2
1227P1227Accelerator pedal position (APP)   sensor 2 – voltage lowWiring, APP sensor, ECM
1228P1228Accelerator pedal position (APP)   sensor 2 – voltage highWiring, APP sensor, ECM
1229P1229Sensor supply voltage – short circuitWiring, APP sensor, TP sensor, MAF sensor, EVAP sensor, PS sensor, refrigerant sensor, ECM
1233P1233Electronic throttle control – performanceWiring, throttle control motor
1234P1234Throttle motor position sensor – learning problem, voltage low, bank 2Wiring, TP sensor 1, TP sensor 2
1235P1235Throttle motor pos tion sensor – learning problem, bank 2Wiring, TP sensor 1, TP sensor 2
1236P1236Throttle control motor – short circuitWiring, throttle control motor
1238P1238Throttle control motor – malfunctionThrottle control motor
1239P1239Throttle position (TP) – performanceWiring, throttle actuator, TP sensor
1271P1271Heated oxygen sensor (H02S), bank 1 – voltage lowWiring, H025
1272P1272Heated oxygen sensor (H02S), bank 1 – voltage highWiring, H025
1273P1273Heated oxygen sensor (H02S), bank 1 – lean mixtureH025, fuel pressure, injectors, intake air leak
1274P1274Heated oxygen sensor (H02S), bank 1 – rich mixtureH025, fuel pressure, injector,s
1276P1276Heated oxygen sensor (H02S), bank 1 – activityWiring, H025
1278P1278Heated oxygen sensor (H02S), bank 1 – slow responseWiring, fuel pressure, injectors, MAF sensor, PCV, H025, intake air leaks, exhaust leaks
1279P1279Heated oxygen sensor (H02S), bank 1 – slow responseWiring, fuel pressure, injectors, MAF sensor, PCV, H025, intake air leaks, exhaust leaks
1335P1335Crankshaft position (CKP) sensor 2 – circuit malfunctionWiring, CKP sensor, ECM
1336P1336Crankshaft position (CKP) sensor 1 – rotor teeth damageWiring, CKP sensor, ECM
1281P1281Heated oxygen sensor (H02S), bank 2 – voltage lowWiring, H025
1282P1282Heated oxygen sensor (H02S), bank 2- voltage highWiring, H025
1283P1283Heated oxygen sensor (H02S), bank 2 – lean mixtureH025, fuel pressure, injectors, intake air leak
1284P1284Heated oxygen sensor (H02S), bank 2 – rich mixtureH02S, fuel pressure, injectors
1286P1286Heated oxygen sensor (H02S), bank 2- activityWiring, H02S
1288P1288Heated oxygen sensor (H02S), bank 2 – slow responseWiring, fuel pressure, injectors, MAF sensor, PCV, H02S, intake air leaks, exhaust leaks
1289P1289Heated oxygen sensor (H02S), bank 2 – slow responseWiring, fuel pressure, injectors, MAF sensor, PCV, H02S, intake air leaks, exhaust leaks
1290P1290Throttle control motor relay – voltage lowWiring, relay
1400P1400Exhaust gas recirculation (EGR) system/ evaporative emission (EVAP) canister purge system – valve malfunctionWiring, EGRIEVAP valve, ECM
1402P1402Exhaust gas recirculation (EGR) system – excessive flowWiring, EGR/EVAP valve, EGR valve, EGRT sensor, EGR back pressure transducer, ECM
1421P1421Cold start emission control – malfunctionIntake/exhaust leak/blockage, mechanical fault, idle speed control (ISC) system, ignition control, engine coolant temperature (ECT) sensor, H02S, ECM
1442P1442Evaporative emission (EVAP) canister purge system – small leakWiring, fuel tank/cap, hose leak/blockage, EVAP valve/canister, EVAP vent valve, BARO sensor, MAP/BARO switching valve, ECM
1444P1444Evaporative emission (EVAP) canister purge system – control valve malfunctionWiring, EVAP pressure sensor, hose leak/blockage, EVAP valve/canister, ECM
1446P1446Evaporative emission (EVAP) canister purge system – vent control valve malfunctionWiring, EVAP pressure sensor, hose leak/blockage, EVAP vent valve, EVAP canister contaminated, ECM
1448P1448Evaporative emission (EVAP) canister purge system – vent control valve malfunctionWiring, EVAP vent valve, EVAP pressure sensor, hose leak/blockage, EVAP canister contaminated, EVAP vacuum cut valve, ECM
1456P1456Evaporative emission (EVAP) canister purge system – very small leakWiring, fuel tank/cap, hose leak/blockage, EVAP valve/canister, EVAP vent valve, BARO sensor, MAP/BARO switching valve, ECM
1464P1464Fuel tank level sensor- voltage highWiring, fuel tank level sensor
1480P1480Engine coolant blower motor control – circuit malfunctionWiring, blower motor speed control solenoid valve, ECM
1490P1490Evaporative emission (EVAP) canister purge system – bypass vacuum valve malfunctionWiring, EVAP bypass/cut valve, hose leak/blockage, ECM
1491P1491Evaporative emission (EVAP) canister purge system – bypass vacuum valve malfunctionWiring, EVAP vacuum cut/bypass valve, hose leak/blockage, EVAP pressure sensor/vent valve, EVAP canister contaminated, ECM
1550P1550Electrical load sensor – circuit malfunctionWiring, electrical load sensor, ECM
1551P1551Electrical load sensor, circuit low – circuit malfunctionWiring, electrical load sensor, ECM
1552P1552Electrical load sensor, circuit high – circuit malfunctionWiring, electrical load sensor, ECM
1553P1553Electrical load sensor – circuit malfunctionWiring, electrical load sensor, ECM
1554P1554Electrical load sensor – circuit malfunctionWiring, electrical load sensor, ECM
1564P1564Cruise control master switch – malfunctionWiring, cruise control master switch, ECM
1572P1572Cruise control brake switch – circuit malfunctionWiring, cruise control brake switch, stop lamp switch, clutch pedal switch, ECM
1574P1574Cruise control vehicle speed sensor – signal variation between two vehicle speed sensorsWiring, CAN data bus, vehicle speed sensor, instrument panel, ECM
1605P1605TCM diagnosis communication line – malfunctionWiring, TCM
1610P1610Ignition key/engine control module (ECM) – malfunctionIncorrect ignition key, ECM
1611P1611Immobilizer control module/engine control module (ECM) – codingImmobilizer control module/ECM   incorrectly coded
1612P1612Immobilizer control module/engine control module (ECM) communication – malfunctionWiring, immobilizer control module, ECM
1613P1613Engine control module (ECM), immobilizer function – internal failureECM
1614P1614Immobilizer control module/module coding plug communication – no signalWiring, immobilizer control module, module coding plug
1615P1615Ignition key/immobilizer control module communication – malfunctionIncorrect ignition key, immobilizer control module
1705P1705AT – throttle position (TP) sensor- voltage high or lowWiring, TP sensor, TCM, ECM
1706P1706Park/neutral position (PNP) switch – circuit malfunctionWiring, PNP switch, ECM
1715P1715Transmission input shaft speed (ISS)   sensor – circuit malfunctionWiring, ECM
1716P1716Automatic transmission turbine revolution sensor – circuit malfunctionWiring, turbine sensor 1, turbine sensor 2, ECM
1720P1720Vehicle speed sensor (VSS) – signal variationWiring, mechanical fault, ABSfTCS   control module, TCM
1730P1730Automatic transmission fail safe function – circuit malfunctionWiring, transmission clutches, transmission solenoid valves, transmission pressure switches
1740P1740CVT lock-up select solenoid valve – malfunctionWiring, lock-up select solenoid valve
1752P1752Automatic transmission input clutch – solenoid valve malfunctionWiring, input clutch solenoid valve
1754P1754Automatic transmission input clutch – solenoid valve malfunctionWiring, input clutch solenoid valve, ·   transmission pressure switch 3
1757P1757Automatic transmission front brake – solenoid valve malfunctionWiring, front brake solenoid valve
1759P1759Automatic transmission front brake – solenoid valve malfunctionWiring, front brake solenoid valve, transmission pressure switch 1
1760P1760AT – overrun clutch solenoid – voltage lowWiring, overrun clutch solenoid, TCM
1762P1762Automatic transmission direct clutch – solenoid valve malfunctionWiring, direct clutch solenoid valve
1764P1764Automatic transmission direct clutch – solenoid valve malfunctionWiring, direct clutch solenoid valve, transmission pressure switch 5
1767P1767Automatic transmission high/low reverse – solenoid valve malfunctionWiring, high/low reverse solenoid valve
1769P1769Automatic transmission high/low reverse – solenoid valve malfunctionWiring, high/low reverse solenoid valve, transmission pressure switch 6
1772P1772Automatic transmission low coast brake – solenoid valve malfunctionWiring, low coast brake solenoid valve
1774P1774Automatic transmission low coast brake – solenoid valve malfunctionWiring, low coast brake solenoid valve, transmission pressure switch 2
1777P1777CVT step motor – circuit malfunctionWiring, step motor
1778P1778CVT step motor – mechanical malfunctionStep motor
1780P1780Automatic transmission shift change – signal malfunctionWiring, TCM, ECM
1800P1800Intake manifold air control solenoid – malfunctionWiring, intake manifold air control solenoid, ECM
1805P1805Brake pedal position (BPP) switch – circuit malfunctionWiring, BPP switch, ECM