Mitsubishi OBD / OBD2 Codes

Mitsubishi Trouble Code Info

96 & later are OBD2 systems and require a scanner.

Accessing Diagnostic Trouble Codes

  • Turn ignition switch to OFF position
  • Locate Data Link Connector (DLC), next to fuse box.
  • Connect voltmeter positive lead to DLC terminal #1 and Negative lead to terminal #12 (ground).
  • Turn Ignition switch to ON position.
  • codes are read out by 12 volt pulses of voltmeter.
  • A constant repetition of short pulses is normal.
  • Signals will appear on voltmeter a long and short 12 volt pulses.
  • long pulses represent tens
  • short pulses represent ones (4 long pulses and 3 short pulses indicates code 43)

94-95 Mitsubishi Diamante Retrieval Without Scan Tool Other 95 models require a diagnostic trouble code check harness(part # MB991529) to ground terminal #1 images used with permission Copyright © 2001 ALLDATA LLC.
  1. Ground Data Link Connector terminal # 1.
  2. Set the ignition switch to “ON”, the Malfunction Indicator (check engine) Lamp will illuminate for a particular duration and a certain number of times.
  3. Clear the trouble codes by disconnecting the vehicle battery negative terminal for 16 seconds or longer
EXAMPLES
No Codes–normal
  • The Lamp will illuminate for 0.5 seconds, then stay Off for 0.5 seconds, this pattern will repeat until the ignition is turned OFF.
Code 13
  • The Lamp will illuminate one time for approximately 0.5 second. This will represent one unit of ten. There will be approximately a one second delay and then the Lamp will illuminate three times for approximately 0.2 seconds with 0.2 second delay between deflections. This will represent three units of one.
Code 23
  • The Lamp will illuminate two times for approximately 0.5 second with approximately 0.3 second delay between deflections. This will represent two units of ten. There will be approximately a one second delay and then the Lamp will illuminate three times for approximately 0.2 seconds with 0.2 second delay between deflections. This will represent three units of one..

Clearing Trouble Codes

Diagnostic trouble codes may be cleared by disconnecting the battery ground cable for at least 20 seconds. Reconnect negative battery cable and recheck codes to confirm the repair.

Diagnostic Codes

Mitsubishi

 
Without OBD-II
11 Oxygen sensor fault.
12 Airflow sensor fault.
13 Intake air temp sensor fault.
14 Throttle position sensor (TPS) fault.
15 Idle speed control (ISC) motor position sensor fault.
21 Coolant temp sensor fault.
22 Crankshaft position (CKP) sesnor fault.
23 Camshaft position (CMP) sensor fault.
24 Vehicle speed sensor (VSS) fault.
25 Barometric (BARO) pressure sensor fault.
31 Knock sensor fault.
32 MAP sensor faulty.
36 Ignition timing adjustment signal fault.
39 Oxygen (O2) sensor fault.
41 Injector(s) fault
42 Fuel pump fault.
43 EGR fault.
44 Ignition coil (cylinders #1 & #4) fault.
52 Ignition coil (cylinders #2 & #5) fault.
53 Ignition coil (cylinders #3 & #6) fault.
55 Idle air control (IAC) valve position sensor fault.
59 Rear Oxygen (O2) sesnor fault.
61 Transaxle control module torque reduction signal fault.
62 Variable Induction control (VIC) valve position sensor fault.
71 Traction control (TC) vacuum valve solenoid fault.
72 Traction Control (TC) vent valve solenoid fault.
ECI Voltmeter or Test Light
1 Oxygen Sensor.
2 Ignition Signal.
3 Air Flow Sensor.
4 Pressure Sensor.
5 Throttle Position Sensor.
6 Idle Speed Control Motor Position Switch.
7 Engine Coolant Temperature Sensor.
MPFI 86-88 4 Cyl. Voltmeter or Test Light
10000 Oxygen Sensor.
01000 Crank Angle Sensor.
11000 Air Flow Sensor.
00100 Atmospheric Pressure Sensor.
10100 Throttle Position Sensor.
01100 Motor Position Sensor.
11100 Engine Coolant Temperature Sensor.
00010 No. 1 Cylinder TDC Sensor.
MPFI V6 and 89-95 4 Cyl. (Exc. 95 Eclipse) Voltmeter or Test Light
11 Oxygen Sensor.
12 Air Flow Sensor.
13 Intake Air Temperature Sensor.
14 Throttle Position Sensor.
15 Motor Position Sensor.
21 Engine Coolant Temperature Sensor.
22 Crank Angle Sensor.
23 TDC/CMP Sensor.
24 Vehicle Speed Sensor.
26 BARO Sensor.
31 Knock Sensor.
32 Manifold Absolute Pressure Sensor.
36 Ignition Timing Adjustment Signal.
39 Oxygen Sensor.
41 Injector.
42 Fuel Pump.
43 EGR.
44 Ignition Coil, 4 Cylinder.
44 Ignition Coil Power Transistor Unit, V6 Cylinders 1 & 4.
52 Ignition Coil Power Transistor Unit, V6 Cylinders 2 & 5.
53 Ignition Coil Power Transistor Unit, V6 Cylinders 3 & 6.
55 Idle Air Control Valve/Servo Valve Position Sensor.
59 Oxygen Sensor (Rear), 4 Cylinder.
59 Left hand Bank Heated Oxygen Sensor, V6.
61 Cable from Transaxle Control Unit, For Transmission
61 Torque Reduction Signal (A/T).
62 Induction Control Valve Position Sensor (Non Turbo).
69 Right hand Bank Heated Oxygen Sensor.
71 Traction Control Vacuum Solenoid.
72 Traction Control Ventilation Solenoid.
  95-98 Eclipse (Non-Turbo) Retrieval Without Scan Tool
  1. Cycle the ignition key On-Off-On-Off-On within 5 seconds.
images used with permission Copyright © 2001 ALLDATA LLC.
  1. Count the number of times the malfunction indicator lamp (check engine lamp) on the instrument panel flashes on and off. The number of flashes represents the trouble code. There is a slight pause between the flashes representing the first and second digits of the code. Longer pauses (approx. 4 seconds) separate individual trouble codes.
  • Repair the malfunction while referring to the inspection chart for diagnostic trouble codes.
 
  • After disconnecting the battery cable from the battery (-) terminal for 10 seconds or more, reconnect the cable.
  • Start the engine and run it at idle for about 15 minutes after the engine has warmed up.
MPFI 95-98 Eclipse (Non-Turbo) Check Engine/Light Scan Tool
11 Intermittent Loss Of Crankshaft Position Sensor.
11 Misfire Adaptive Numerator at Limit.
11 No Crankshaft Reference Signal at PCM.
11 Timing Belt Skipped 1 Tooth or More.
13 No Change In Manifold Absolute Pressure (MAP) From Start To Run.
14 5-Volt Supply Output Too Low.
14 Manifold Absolute Pressure (MAP) Sensor Voltage Too High.
14 Manifold Absolute Pressure (MAP) Sensor Voltage Too Low.
14 No 5 Volts To Manifold Absolute Pressure (MAP) Sensor.
15 No Vehicle Speed Sensor Signal.
16 Knock Sensor No. 1 Circuit.
17 Closed Loop Temperature Not Reached.
17 Engine Is Cold Too Long.
21 Downstream Heated Oxygen Sensor Heater Failure.
21 Downstream Heated Oxygen Sensor Shorted To Voltage.
21 Downstream Heated Oxygen Sensor Stays at Center.
21 Downstream Heated Oxygen Sensor Stays at Center.
21 Downstream Heated Oxygen Sensor Voltage Grounded.
21 Slow Upstream Heated Oxygen Sensor Circuit during Catalyst Monitor.
21 Upstream Heated Oxygen Sensor Heater Failure.
21 Upstream Heated Oxygen Sensor Response.
21 Upstream Heated Oxygen Sensor Shorted To B+.
21 Upstream Heated Oxygen Sensor Stays at Center.
21 Upstream Heated Oxygen Sensor Voltage Grounded.
22 Engine Coolant Temperature Sensor Voltage High.
22 Engine Coolant Temperature Sensor Voltage Low.
23 Intake Air Temperature Sensor Voltage High.
23 Intake Air Temperature Sensor Voltage Low.
24 No 5 Volts To Throttle Position Sensor.
24 Throttle Position Sensor Voltage Disagrees With Manifold Absolute Pressure.
24 Throttle Position Sensor Voltage High.
24 Throttle Position Sensor Voltage Low.
25 Idle Air Control Motor Circuits.
25 Target Idle Not Reached (plus or minus 200 RPM).
27 Injector No. 1 Control Circuit.
27 Injector No. 2 Control Circuit.
27 Injector No. 3 Control Circuit.
27 Injector No. 4 Control Circuit.
31 EVAP Leak Monitor Pinched Hose found.
31 EVAP Purge Flow Monitor Failure.
31 EVAP Solenoid Circuit.
31 EVAP Solenoid Switch or Mechanical Fault.
31 EVAP System Large Leak.
31 EVAP System Small Leak.
31 EVAP Vent Solenoid Circuit.
31 Engine Coolant Temp sensor voltage too high.
32 EGR Solenoid Circuit.
32 EGR System Failure.
33 A/C Clutch Relay Circuit.
35 High Speed Fan Control Relay Circuit.
35 High Speed Radiator Fan Relay Circuit.
35 Low Speed Fan Control Relay Circuit.
36 PAIR Solenoid Circuit – M/T.
36 Too Little or Too Much Secondary Air.
37 Park/Neutral Position Switch Failure.
41 Alternator Field Not Switching Properly.
42 Fuel Level Sensing Unit Voltage Too High.
42 Fuel Level Sensing Unit Voltage Too Low.
42 Fuel Level Unit No Change Over Miles.
42 Fuel Pump Relay Control Circuit.
42 MFI (ASID) Relay Control Circuit.
42 No MFI (ASD) Relay Output Voltage at PCM.
43 Cylinder No. 1 Misfire.
43 Cylinder No. 2 Misfire.
43 Cylinder No. 3 Misfire.
43 Cylinder No. 4 Misfire.
43 Ignition Coil No. 1 Primary Circuit.
43 Ignition Coil No. 2 Primary Circuit.
43 Multiple Cylinder Misfire.
44 Battery Temperature Sensor Voltage Too High.
44 Battery Temperature Sensor Voltage Too Low.
44 Battery Temperature Voltage out of limit.
45 EATX Controller Trouble Code Present.
46 Charging System Voltage Too High.
47 Charging System Voltage Too Low.
51 Fuel System Lean.
52 Fuel System Rich.
53 Internal Controller Failure.
53 PCM Failure – Serial Peripheral Interface Communications.
54 No Cam Signal at PCM.
61 BARO Pressure Out Of Range.
62 PCM Failure – Service Reminder Indicator Mile Not Stored.
63 PCM Failure – EEPROM Write Denied.
64 Catalytic Converter Efficiency Failure.
65 Power Steering Pressure Switch Failure.
66 No CCD Messages From TCM – A/T.
 
95 Eclipse (Turbo) 96-98 Vehicles OBD2
P0100 Volume Air Flow circuit.
P0105 BARO Pressure circuit.
P0110 Intake Air Temperature circuit.
P0115 Engine Coolant Temperature circuit.
P0120 Throttle Position circuit.
P0125 Excessive Time to Enter Closed Loop Fuel Control.
P0130 Heated Oxygen Sensor circuit Bank 1 Sensor 1.
P0135 Heated Oxygen Sensor Heater circuit Bank 1 Sensor 1.
P0136 Heated Oxygen Sensor circuit Bank 1 Sensor.
P0141 Heated Oxygen Sensor Heater circuit Bank 1 Sensor 2.
P0150 Heated Oxygen Sensor circuit Bank 2 Sensor 1.
P0155 Heated Oxygen Sensor Heater circuit Bank 2 Sensor 1.
P0156 Heated Oxygen Sensor circuit Bank 2 Sensor 2.
P0161 Heated Oxygen Sensor Heater circuit Bank 2 Sensor 2.
P0170 Fuel Trim Bank 1.
P0173 Fuel Trim Bank 2.
P0201 Injector circuit – Cylinder 1.
P0202 Injector circuit – Cylinder 2.
P0203 Injector circuit – Cylinder 3.
P0204 Injector circuit – Cylinder 4.
P0205 Injector circuit – Cylinder 5.
P0206 Injector circuit – Cylinder 6.
P0300 Random Misfire Detected.
P0301 Misfire Detected – Cylinder 1.
P0302 Misfire Detected – Cylinder 2.
P0303 Misfire Detected – Cylinder 3.
P0304 Misfire Detected – Cylinder 4.
P0305 Misfire Detected – Cylinder 5.
P0306 Misfire Detected – Cylinder 6.
P0325 Knock Sensor 1 circuit.
P0335 Crankshaft Position Sensor circuit.
P0340 Crankshaft Position Sensor circuit.
P0400 EGR Flow.
P0403 EGR Solenoid.
P0420 Catalytic Efficiency below threshold (Bank 1).
P0421 Warm-Up Catalyst Efficiency below threshold (Bank 1).
P0431 Warm-Up Catalyst Efficiency below threshold (Bank 2).
P0440 EVAP System.
P0442 EVAP System Leak Detected.
P0443 EVAP System Purge Control Valve circuit.
P0446 EVAP System Vent Control.
P0450 EVAP System Pressure Sensor.
P0455 EVAP Control System Leak Detected.
P0500 Vehicle Speed Sensor.
P0505 Idle Control System.
P0510 Closed Throttle Position Switch.
P0551 Power Steering Pressure Sensor circuit Range/Performance.
P0700 Transaxle Control System.
P0705 Transmission Range Sensor circuit (PRNDL – Input).
P0710 Transmission Fluid Temperature Sensor circuit.
P0715 Input/Turbine Speed Sensor circuit.
P0720 Output Speed Sensor circuit.
P0725 Engine Speed Input circuit.
P0740 Torque Converter Clutch System.
P0750 Shift Solenoid “A”.
P0755 Shift Solenoid “B”.
P0760 Shift Solenoid “C”.
P0765 Shift Solenoid “D”.
P1103 Turbocharger Wastegate Actuator.
P1104 Turbocharger Wastegate Solenoid.
P1105 Fuel Pressure Solenoid.
P1300 Ignition Timing Adjustment circuit.
P1400 Manifold Differential Pressure Sensor circuit.
P1500 Alternator FR Terminal circuit.
P1600 Serial Communication Link.
P1715 Pulse Generator Assembly.
P1750 Solenoid Assembly.
P1751 A/T Control Relay.
P1791 Engine Coolant Temperature Level Input circuit.
P1795 Throttle Position Input circuit to TCM.
Information and Images used with permission Copyright © 2001 ALLDATA LLC.
Model Year Engine identification System
3000GT 1994-95 6G72 DOHC Mitsubishi MPI
3000GT 1996-99 6G72 Mitsubishi MPI
3000GT Turbo 1994-95 6G72 DOHC Mitsubishi MPI
3000GT Turbo 1996-99 6G72 Mitsubishi MPI
Diamante 3.0L 1994-95 6G72 Mitsubishi MPI
Diamante 3.0L 1996 6G72 Mitsubishi MPI
Diamante 3.5L 1997-04 6G74 Mitsubishi MPI
Eclipse 2.0L 1995-99 420A Mitsubishi MPI
Eclipse 2.0L Turbo 1995-99 4G63 Mitsubishi MPI
Eclipse 2.4L 1996-09 4G64/4G69 Mitsubishi MPI
Eclipse 3.0L 2000-05 6G72 Mitsubishi MPI
Eclipse 3.8L 2006-09 6G75 Mitsubishi MPI
Endeavor 3.8L 2004-08 6G75 Mitsubishi MPI
Expo 2.4L 4X4 – California 1996 4G64 Mitsubishi MPI
Expo LRV 1.8L – California 1995-96 4G93 Mitsubishi MPI
Expo LRV 1.8L – Federal 1996 4G93 Mitsubishi MPI
Expo/LRV 2.4L FWD – California 1995-96 4G64 Mitsubishi MPI ·
Expo/LRV 2.4L – Federal 1996 4G64 Mitsubishi MPI
Galant 2.4L 1994-95 4G64 Mitsubishi MPI
Galant 2.4L 1996-09 4G64 Mitsubishi MPI
Galant 3.0L 1999-03 6G72 Mitsubishi MPI
Galant 3.8L 2004-09 6G75 Mitsubishi MPI
Lancer 2.0L 2002-07 4G94 Mitsubishi MPI
Lancer 2.0L 2008-09 4811 Mitsubishi MPI
Lancer Evolution 2.0L 2003-07 4G63 Mitsubishi MPI
Lancer Evolution 2.4L 2008-09 4812 Mitsubishi MPI
Lancer Sportback 2.4L 2002-06 4G69 Mitsubishi MPI
Mighty Max Pickup 2.4L 1990-95 4G64 Mitsubishi MPI
Mighty Max Pickup 2.4L 1996 4G64 Mitsubishi MPI
Mighty Max Pickup 3.0L 1990-96 6G72 Mitsubishi MPI
Mirage 1.5/1.8L 1995-02 4G15/4G93 Mitsubishi MPI
Mirage 1.8L- California 1994 4G93 Mitsubishi MPI
Mirage 1.8L – Federal 1994-95 4G93 Mitsubishi MPI
Montero 3.0L 1989-93 6G72 Mitsubishi MPI
Montero 3.0L 1994-95 6G72 Mitsubishi MPI
Montero 3.0L 1996-06 6G72 Mitsubishi MPI
Montero 3.5L 1996-06 6G74 Mitsubishi MPI
Montero 3.8L 2004-06 6G75 Mitsubishi MPI
Montero Sport 2.4L 1997-99 4G64 Mitsubishi MPI
Montero Sport 3.0L 1996-03 6G72 Mitsubishi MPI
Montero Sport 3.5L 1996-04 6G74 Mitsubishi MPI
Outlander 2.4/3.0L 2003-08 4G64/4G69/6831 Mitsubishi MPI
Raider 3.7/4.7L 2006-08 EKG/EGA Chrysler MFI

10 Replies to “Mitsubishi OBD / OBD2 Codes”

  1. Prosze mi powiedziec jak i czym sie podpiac do eclipsy z 16 pinami jak jest na rysunku . co to znaczy ..Złącze łącza danych naziemnych nr 1.. Jest narysowany jeden kabelek i pytanie jaki i od czego ??

    Reply

  2. Good morning friend:
    The codes in the first table apply for the mitubishi dakar L200, from 2006?
    The scan of my pick up yields the following trouble codes:
    12, 13 and 52. Could you help me identify them?
    Regards;
    Ebert Paredes

    Reply

  3. i have a 2000 Mitsubishi challenger with a 6g74 engine in it and its has the code 36 ignition timing adjustment signal fault cant anyone guide me on how to fix this problem ?

    Reply

  4. 1996 Mitsubishi challenger petrol. Abs light staying on. Would a abd 2 reset tool do the job. One of the terminals was corroded so cleaned it up. Thanks

    Reply

  6. 1996 Monteiro SR, codes will not show ready after multiple offs and on, multiple miles driven and battery disconnected and reconnected before all of that

    Reply

  7. I have a 2002 Mitsu Montero Sport that recently failed the Oregon DEQ test. The reason was due to the “Diagnostic Trouble Code” P0431. “Catalyst 1 Effeciency Below Threshold- Bank 2” What does this mean? What is required to repair it? Possibly, at what cost?

    The DEQ deadline to have this repair done is in a few days.

    Thanks

    Please send reply to my email.

    Reply

    1. Tom. This code is due to a plugged or defective catalytic convertor. Each convertor costs different but the usual cost of the part is around $200. If not a direct fit, some welding must be done. I would prepare to pay $200+. Good luck.

      Reply

  8. I have a 4g94 engine
    Which have a fault code P0300 ( random/ multiple misfire )

    What should I do to solve this problem ?!

    Reply

Leave a Reply to sef Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.