C1306 – Steering angle sensor
| Code | Fault Location | Probable Cause |
|---|---|---|
| C1306 | Steering angle sensor (Buy Part On Amazon) | Improper replacement or recalibration procedure, Wheel alignment, Wiring, Steering angle sensor, Low system voltage, Fuses, BCM failure |
We recommend Torque Pro
Table of Contents
- What Does Code C1306 Mean?
- Where is the C1306 sensor located?
- What are the common causes of code C1306?
- What are the symptoms of code C1306?
- Get Help with C1306
What Does Code C1306 Mean?
OBD II fault code C1306 is a manufacturer specific code that is defined by carmaker Mazda as “Steering angle sensor”, and is set on Mazda applications when the PCM (Powertrain Control Module) and/or BCM (Body Control Module) detects a failure, malfunction, or defect in the steering angle sensor itself, as opposed to a failure, malfunction, or defect in the steering angle sensor’s wiring.
NOTE: Be aware that most official Mazda sources define code C1306 either as-
- “Steering Angle Sensor Calibration”, or as
- “Steering Wheel Angle Sensor Zero Position Not Found”
While the above definitions can also refer to a failure, malfunction, or defect in the steering angle sensor, the official Mazda definitions more specifically refers to an issue with the steering angle sensors’ calibration.
The steering angle sensor on Mazda applications forms part of a complex communications network that includes the PCM, ABS brake system, and driver assist systems such as the cruise control, stability control, traction control systems, and on applications with automatic transmissions, the transmission as well. Depending on the application, other systems might include hill descent, electronic brake distribution, autonomous braking, and others.
Nonetheless, the function of the steering angle sensor within the greater network is to monitor the position of the steering angle relative to the vehicles’ thrust line. Put differently, this means that the steering angle sensor monitors the position of the front wheels relative to an imaginary line that runs through the long axis of the vehicle to ensure that the vehicle moves in a straight line when the steering wheel in the dead-ahead position.
As a practical matter, when the vehicle moves in a straight line, the wheels all rotate at the same speed, which the PCM interprets as a stable condition. However, if the wheels on one side of the vehicle start to rotate at a different rate than the wheels on the other side of the vehicle due to a steering input, both the angle of the input, and the rate at which the input is made is measured by the steering angle sensor. This information is then compared to inputs from the wheel speed sensors and based on the differences in the rotational speeds of the wheels, as well as the vehicle’s road speed, one or more control modules might deduce that a situation is developing that might affect the stability of the vehicle.
Under these conditions the PCM and ABS control module might apply selective braking forces to individual wheels via the ABS system to restore or maintain the vehicle’s stability; however, whether or not this happens depends entirely on the rationality of the information received from the steering angle sensor. It should be noted that input data from the steering angle sensor forms the foundation of all corrective actions performed by the ABS and other safety systems when potentially dangerous situations such as skids or slides occur, when the vehicles’ weight is suddenly transferred from one side to the other, or when sudden and large steering inputs are detected.
Thus, if a fault, malfunction, or failure exists in the steering angle sensor that prevents the sensor from relaying accurate/rational data to the PCM and other control modules, the PCM will recognize that it cannot control, correct, or maintain the vehicles’ stability effectively, and it will set code C1306 and illuminate one or more warning lights as a result. Other actions will include disabling the ABS, traction control, stability control, and all other systems that depend on the ABS system to function. Note though that normal braking will not be affected.
Where is the C1306 sensor located?
The schematic drawing above indicates the location of the steering angle sensor on a Mazda 3 application. Note though that replacement of the steering angle sensor on most Mazda applications requires removal of the steering wheel, which could cause one or more airbags to deploy unless the prescribed procedure to disarm the airbags is followed exactly.
WARNING: Note that deploying air bags inadvertently can cause serious and potentially fatal personal injuries.
What are the common causes of code C1306?
Most common causes of code C1306 are much the same across most, if not all Mazda applications and could include one or more of the following-
- Improper replacement procedures during steering angle sensor replacement(s)
- Failure to perform the prescribed recalibration procedure after wheel alignment procedures or suspension/steering system repairs
- Collisions with road debris, potholes, or other obstructions that could have disturbed wheel alignment settings
- Damaged, burnt, shorted, disconnected, or corroded wiring and/or connectors in associated wiring
- Defective steering angle sensor
- Disconnecting and reconnecting the steering angle sensors’ wiring during unrelated repairs
- Interruption of system power by disconnecting the battery
- Low system voltages caused by a defective or discharged battery
- Removal or replacement of fuses, and particularly the fuse labeled “ROOM”. Note that this fuse is numbered differently on different Mazda applications
- Failed or failing BCM (Body Control Module)
What are the symptoms of code C1306?
Symptoms of code C1306 on Mazda applications are largely similar, and could include the following-
- Stored trouble code(s) and one or more illuminated warning lights
- Traction-, stability-, and ABS systems may be deactivated automatically
- Steering may have a “sloppy” feel, and steering responses may be sluggish, exaggerated, or unpredictable. Note that this particular symptom could worsen at moderate to high road speeds, which could make it extremely dangerous, and sometimes impossible to operate the vehicle safely
- It may be difficult to turn the steering wheel in either direction at all road speeds
- Position of the steering wheel may deviate from the strictly “dead-ahead” position when the vehicle is travelling in a straight line
Help Us Help You
Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.
Reading C1306 on your car
C1306 is a chassis code. Most inexpensive Bluetooth adapters read generic engine codes only and cannot reach these systems at all – reading it, and getting the manufacturer’s own description of the fault, needs a scanner that talks to the other modules.
