P0455 – EVAP System Large Leak (Jeep)

Avatar photo
By Reinier (Contact Me)
Last Updated 2023-09-14
Automobile Repair Shop Owner
CodeFault LocationProbable Cause
P0455 EVAP System Large Leak
(Buy Part On Amazon)

We recommend Torque Pro

Table of Contents

  1. What Does Code P0455 Mean?
  2. Where is the P0455 sensor located?
  3. What are the common causes of code P0455?
  4. What are the symptoms of code P0455?
  5. Get Help with P0455

What Does Code P0455 Mean?

SPECIAL NOTES: Although generic OBD II trouble codes such as P0455 – “EVAP System Large Leak”  can and do affect all OBD II compliant vehicles, some vehicle makes and models are sometimes more susceptible to some generic trouble codes than others under real-world driving and operating conditions. Therefore, this article will discuss generic trouble code P0455 – “EVAP System Large Leak” as it applies to the Jeep models that are most commonly affected by it. END OF SPECIAL NOTES.

OBD II fault code P0455 is a generic trouble code that is defined as, P0455 – “EVAP System Large Leak”, or sometimes as P0455 – “Evaporative Emission System Leak Detected (large leak), and is set when the PCM (Powertrain Control Module) detects a gross leak in the EVAP system. Note that while EVAP (Evaporative Emissions Control ) systems can generally not determine the exact size of a leak, large or gross leaks are typically taken to be leaks that are larger than about 0.020 inches in diameter.

Although the technical implementation of EVAP systems varies greatly between different vehicle makes and models, the function of all EVAP systems on all vehicle makes and models is to trap and contain fuel vapors in a charcoal-filled canister until the trapped vapors can be transported to the engine to be combusted along with the regular air/fuel mixture.

However, for emission control purposes, all EVAP systems have to incorporate a leak detection system that is capable of performing self-diagnostic tests at certain points before, during, and after trips to verify the integrity of the EVAP system. In practice, all EVAP systems use all of the components of the system to perform self-tests, and these components include the fuel tank itself, the fuel filler cap, various vacuum hoses, a charcoal canister, vent, and purge valves, and a variety of pressure and flow sensors.

However, in the case of Jeep vehicles, the EVAP system also incorporates a dedicated air pump whose function is to pressurize the fuel system during self-tests. Here is how the EVAP leak detection system works-

When a self-test is initiated, the PCM closes both the vent and purge valves to seal the fuel system from the atmosphere. Next, the PCM starts the air pump to pressurize the fuel system until the pressure (in the system) reaches a predetermined level as reported by a dedicated pressure sensor on or near the fuel tank. In a fully functional EVAP system, the pressure in the fuel system will remain constant, which indicates the absence of leaks.

If a leak is present, however, the pressure in the fuel system will escape through the leak path, and the PCM will infer the size or magnitude of the leak based on the rate of the pressure loss in the fuel system, which in the case of trouble code P0455, will be a leak of about 0.20 inches in diameter.

Nonetheless, to improve the accuracy of self-tests, several enabling conditions must be satisfied before an EVAP  self-test will initiate. These include, among others, the ambient temperature being within a predefined range and the fuel tank being between about 25 percent and about 75 percent full.

It should be noted, though, that although the presence of leaks in the EVAP system will not influence the normal operation of the vehicle, the EVAP system is considered to be a primary emissions control system and, therefore, the PCM will set an appropriate code and illuminate a warning light when it detects leaks in the EVAP system.

Where is the P0455 sensor located?

Illustration for trouble code P0455 – EVAP System Large Leak (Jeep)

This image shows a generic (and much simplified) schematic representation of the principal components of a typical EVAP system. It should be noted that while small leaks can occur almost anywhere in any EVAP system, the vast majority of large leaks occur through the fuel filler cap but in most cases, simply replacing the fuel filler cap with an OEM or OEM-equivalent part will resolve the problem.

What are the common causes of code P0455?

The most common causes of code P0455 are largely similar across all applications and could include one or more of the following-

  • Damaged or defective fuel filler cap
  • The use of a substandard aftermarket fuel filler cap
  • The use of an unsuitable fuel filler cap
  • EVAP vent or purge valve stuck in the open position for whatever reason
  • Damaged charcoal canister
  • Dislodged or perforated EVAP vacuum hoses
  • Improperly executed repair procedures on the EVAP system

What are the symptoms of code P0455?

Common symptoms of code P0455 could include one or more of the following-

Although code P0455 does not cause noticeable, if any drivability symptoms, other symptoms of this code could include one or more of the following-

  • Stored trouble code and an illuminated warning light
  • Depending on the nature of the problem, one or more additional codes may be present along with P0455
  • A strong odor of fuel might be present in or around the vehicle
  • The EVAP readiness monitor may not initiate or run to completion
  • The vehicle will not pass a mandatory emissions test

Help Us Help You

Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.

Reading P0455 on your car

A basic adapter will show you P0455, but not the ABS, airbag or transmission modules, and not the bidirectional tests that confirm which part has actually failed rather than which circuit reported it.

Scanners that read all systems on Amazon