P0780 – Gear selection -shift malfunction (Honda)

By Bojan Popic (Contact Me)
Last Updated 2023-08-22
Master Mechanical Engineer
CodeFault LocationProbable Cause
P0780 Gear selection -shift malfunction
(Buy Part On Amazon)
Clogged TCC solenoid, Inoperable clutch pressure control solenoids

We recommend Torque Pro

Table of Contents

  1. What Does Code P0780 Mean?
  2. Where is the P0780 sensor located?
  3. What are the common causes of code P0780?
  4. Get Help with P0780

What Does Code P0780 Mean?

NOTE: While this guide is specific to Honda vehicles, P0780 is a generic OBD2 diagnostic code. If your vehicle is not a Honda, check the generic version of this guide, as the following information will only apply to some vehicles. If you have a Honda with this code, we hope the detailed information below helps you. Please comment below the article with your year, model, engine type, and mileage, and we will respond and try to help.

The generic description for the P0780 trouble code is Gear selection-shift malfunction, which will be triggered when the vehicle’s automatic transmission fails to engage or disengage the desired gear. This code is almost exclusively caused by a transmission’s internal issues, and to understand why this is so, we’ll briefly explain the working principle behind this drivetrain component.

Illustration for trouble code P0780 – Gear selection -shift malfunction (Honda)

The automatic transmission’s operation is – depending on the car – controlled and regulated either by the Transmission Control Unit (TCU) or Powertrain Control Module (PCM). However, while the electronics are those giving the orders, the actual mechanical work is done by a highly pressurized transmission fluid. More precisely, when a gearshift is to be performed, the control module sends a signal to one or more solenoid valves, which open or close to let the fluid through into appropriate channels and chambers, where they engage or disengage different mechanical components.

In case the TCU/PCM has given all the correct orders to the transmission, but its hydraulics fails to perform the needed operation, the P0780 trouble code will be triggered.

Where is the P0780 sensor located?

As imaginable, gearshift failures are most likely to be caused by automatic transmissions’ initial issues, and those resulting in P0780 trouble codes are no exception. And when looking among potential suspects in this particular case, the transmission solenoids are the first component to check, as these components are the spots where the electrical signals from the TCU/PCM are converted to mechanical movement.

Most of the solenoids are integrated into the valve housing, with access to it being available once the oil pan is removed. Apart from these, there might be several other solenoids fitted around the transmissions’ housing, such as these two pointed out, which activate the clutch assembly.

Illustration for trouble code P0780 – Gear selection -shift malfunction (Honda)

What are the common causes of code P0780?

Generally, the P0780 trouble code can be caused by anything preventing the correct gear shifts. This can be something as simple as low or contaminated transmission fluid, or more complex like faulty solenoids or clogged oil passages. Moreover, as the valve body has its internal wiring, electrical and communicational issues can’t be ruled out, either. All of this is described in detail in the generic version of this guide, so we won’t go over them here. Instead, let’s see what issues are specific to Honda vehicles.

Clogged TCC solenoid

Honda cars from the 2000s with a 5-speed automatic transmission are known to have issues with reappearing P0780 trouble code, which usually pops up when the vehicle is cold. Many owners have found this to be caused by a clogged-up Torque converter clutch solenoid. Instead of trying to clean the dirt, replacing the valve and the corresponding gasket is the only reliable solution.

Illustration for trouble code P0780 – Gear selection -shift malfunction (Honda)

Inoperable clutch pressure control solenoids

Similar to the TCC solenoid mentioned above, the two solenoids that control the clutch pressure can suffer from the same issue. And, likewise, replacing them cures the problem.

Illustration for trouble code P0780 – Gear selection -shift malfunction (Honda)

Help Us Help You

Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.

Reading P0780 on your car

A basic adapter will show you P0780, but not the ABS, airbag or transmission modules, and not the bidirectional tests that confirm which part has actually failed rather than which circuit reported it.

Scanners that read all systems on Amazon