P0341 – Camshaft Position Sensor Incorrect Phase Detected (Honda)
| Code | Fault Location | Probable Cause |
|---|---|---|
| P0341 | Camshaft Position Sensor Incorrect Phase Detected (Buy Part On Amazon) | Timing chains, Abnormal system voltages, Improperly installed camshafts |
Where is the Camshaft position sensor? See our guide to the Camshaft position sensor – what it does, where it sits on the engine and how it fails.
We recommend Torque Pro
Table of Contents
- What Does Code P0341 Mean?
- Where is the P0341 sensor located?
- What are the common causes of code P0341?
- What are the symptoms of code P0341?
- Get Help with P0341
What Does Code P0341 Mean?
SPECIAL NOTES: Although generic OBD II trouble codes such as P0341 – “Camshaft Position Sensor Incorrect Phase Detected” can, and do affect all OBD II compliant vehicles, some vehicle makes and models are sometimes more susceptible to some generic trouble codes than most other vehicle makes and models under real-world driving and operating conditions. Therefore, this article will discuss generic trouble code P0341 as it applies to the Honda models that are most commonly affected by it. END OF SPECIAL NOTES.
OBD II fault code P0341 is a generic trouble code that is defined as, “Camshaft Position Sensor Incorrect Phase Detected”, and is set when the PCM (Powertrain Control Module) detects an implausible or unexpected electrical voltage or signal in the circuits of the camshaft labeled “A” position sensor on bank 1, given the current operating conditions. Note that “Camshaft A” is typically the intake camshaft, while “Bank 1” refers to the bank of cylinders on V-type engines that contains cylinder #1.
NOTE: Be aware that most online databases and trouble code look-up tools list generic code P0341 as “Camshaft Position (CMP) Sensor A, Bank 1 – Range/Performance Problem”. See the section on “Causes” for more details on the significance and implications of the two different definitions of this code. (Italics added for emphasis)
For any four-stroke internal combustion engine to run as intended, the crankshaft and camshafts must be both synchronized and indexed to fixed reference points to ensure that cylinder compression peaks, ignition sparks, and fuel injection events all occur at the optimal point(s) in the pistons’ travel.
Although the above is saying a lot in one breath, we need not delve into the finer details of how engines work here beyond saying that proper camshaft phasing and valid camshaft/crankshaft correlations are crucially important factors in how a PCM calculates fuel delivery and ignition timing strategies. Let us look at these factors in some detail, starting with-
Camshaft phasing
This simply means that the camshafts are phased with respect to each other. As a practical matter, this means that each camshaft opens and closes the valves it serves at the right moment(s) relative to when the other camshafts open and close the valves that each of the other camshafts serves. This ensures-
- that the opening and closing of all the valves on the engine are regulated correctly
- and that open valves cannot come into contact with the tops of the pistons unless a serious mechanical failure of some valve train components occurs
Camshaft/crankshaft correlations
Since the pistons are connected to the crankshaft with connecting rods, the rotation of the crankshaft causes the pistons to move up and down in the cylinders. So, assuming that the camshafts are phased correctly, the crankshaft must be indexed to a fixed reference point relative to the phasing of all the camshafts in the engine to-
- prevent the pistons from coming into contact with open valves
- and to ensure that the pistons are at their optimal positions when all the valves on a given cylinder are closed when a) the compression stroke starts, and b) all the valves on a given cylinder remain closed during the combustion process and subsequent power stroke
When all of the above is true, the positions of all the camshafts in the engine are correlated with the position of the crankshaft, but to maintain the correct correlations on engines with variable valve or camshaft timing, the camshaft position sensors monitor the positions of the camshafts continuously.
The PCM also monitors the position of the crankshaft via a dedicated crankshaft position sensor. Thus, from an engine management perspective, the correct camshaft phasing and camshaft/crankshaft correlation on all modern engines form the basis from which the PCM and other control modules control the ignition and fuel delivery systems, as well as other systems or interfaces, such as the operation of the torque converter lock-up clutch and transmission shift points.
However, intake camshaft position sensors have another function, which is to relay information on the position of the camshaft and hence the valves, on cylinder #1 during the engine starting process. In practice, modern engines start on cylinder #1*, meaning that the PCM needs confirmation that all the valves in cylinder # 1 will be closed when piston #1 approaches its TDC (Top Dead Centre) position when the engine begins to rotate during engine cranking.
* Note that this does not apply to engines with Stop & Go functionality because the starting circuits on these engines are optimized to allow the engine to start on the first available cylinder to limit or reduce engine cranking to a minimum as a means to preserve battery power.
When the above conditions are met, the PCM will deliver an ignition spark and activate the fuel injector on cylinder #1 to allow it to “start”, followed by the other cylinders starting in the firing order that applies to the engine. Note that this strategy typically reduces engine cranking to one engine cycle (720 degrees of crankshaft rotation) during the starting process.
From the above, it should be clear that camshaft position sensors on intake camshafts play a critical role in the highly complex series of events that allows a modern engine to start. We need not delve into the details of this process here, beyond saying that if the PCM detects an implausible or unexpected signal from the intake camshaft’s position sensor, it will usually interpret the implausible or unexpected signal as an improbable or even outright wrong position for the camshaft to be in* relative to the positions both the other camshafts and the crankshaft.
* In the context of code P0341, the term “wrong position” refers to an inappropriate camshaft position as measured in degrees of camshaft rotation relative to one or more fixed reference points.
When such a condition occurs, the PCM will recognize that it cannot control one or more critical engine management functions effectively, and it will set code P0341 and illuminate a warning light as a result.
See the section on “Causes” for more details on the main causes of code P0341 on Honda vehicles.
Where is the P0341 sensor located?
This image shows the location and appearance of the camshaft position sensors on a Honda application. In this example, the yellow arrow indicates the sensor on the intake camshaft (Camshaft “A”), while the red arrow indicates the sensor on the exhaust camshaft.
Note, though, that although camshaft position sensors on Honda engines are typically located in the same or similar position as shown in this example, the actual appearance and method of attachment vary somewhat between different Honda applications. Nonetheless, camshaft position sensors on Honda applications are typically easy to access and replace. Moreover, since camshaft position sensors are of the “plug-and-play” variety, replacing these sensors should be well within the capabilities of even novice non-professional mechanics.
What are the common causes of code P0341?
SPECIAL NOTES: While the definition of generic code P0341 – “Camshaft Position (CMP) Sensor A, Bank 1 – Range/Performance Problem” given above generally means the same thing on all vehicle makes and models, be aware that some official Honda sources define generic code P0341 either as “Improper Phase Detected”, or as “Improper Camshaft Phase Detected”.
The problem with these different definitions is this: camshaft position sensor range or performance issues typically mean that the sensor (or its wiring) is defective or malfunctioning, which might cause one or more camshafts to be out of phase with one or more other camshafts. On the other hand, the phrase “Improper Camshaft Phase Detected” typically means that an actual camshaft phasing issue exists, which condition largely translates into a different set of probable/possible causes and symptoms than those that usually apply to camshaft position sensor range/performance issues.
Moreover, actual camshaft phasing issues and camshaft position sensor range/performance issues require different diagnostic approaches and repair procedures. Therefore, we strongly recommend that you seek professional assistance not with diagnosing code P0341 on any Honda vehicle, but also with determining which code definition applies to the observed symptoms of the code. Failing to do this could lead to confusion and misdiagnoses, which usually leads to needlessly high repair bills when the wrong parts are replaced. END OF SPECIAL NOTES.
Unlike most other vehicle make and models, the probable causes of code P0341 on Honda vehicles are many and varied, but limited space precludes listing all of them here. Nonetheless, the principal causes of code P0341 on many Honda vehicles could include one or more of the following-
Poorly designed timing chains
While it might appear as if stretched timing chains cause camshafts to go out of phase, the fact is that timing chains do not stretch in the same way that, say, a rubber band stretches. In the case of OEM timing chains on Honda vehicles, the rollers in the chain links are subject to increased wear rates, which increases the effective pitch (the distance between chain links) of the chain when the cumulative wear on all the links exceeds a certain threshold.
Although the timing chain tensioner can largely absorb the increased length of the chain, the effective pitch of the chain determines the accuracy of the camshaft phasing. Put differently, this means that although the overall increased length of the chain can be absorbed by the chain tensioner, this necessarily affects the position or phasing of one or more camshafts relative to one or more other camshafts, with the degree of “mis-phasing” depending on the total cumulative wear of all the links in the timing chain.
Abnormal system voltages
Voltage spikes and/or voltage dips caused by discharged batteries and/or defects in charging systems can potentially affect the operation of almost any sensor and/or control module on Honda vehicles. However, it turns out that the most commonly affected sensors on most Honda vehicles are the camshaft position sensors as a function of how most Honda vehicles are wired.
Note that replacing a discharged or defective battery or repairing charging system defects will usually resolve code P0341 automatically on most Honda vehicles.
Improperly installed camshafts
Installing camshafts on most Honda vehicles is a delicate process that requires both special tools and expert-level knowledge of the process if damage to especially a camshaft position sensors’ signal generating components is to be avoided. Therefore, if the camshaft installation process is not performed strictly according to the OEM-recommended procedure, severe damage to the components that generate positional signals is almost guaranteed.
Sadly, this kind of damage caused by inexperienced non-professional mechanics is among the leading cause of code P0341 on many Honda vehicles.
Having said the above, other possible causes of code P0341 could include one or more of the following-
- Damaged, failed, or malfunctioning variable valve timing actuators on one or more camshafts
- Damaged, failed, or malfunctioning variable valve timing oil control solenoids as the result of using dirty, degraded, or contaminated engine oil
- Low oil levels
- Insufficient oil pressure
- Defective or malfunctioning camshaft position sensor(s)
- Damaged, burnt, shorted, or corroded wiring and/or electrical connectors associated with one or more camshaft position sensors
- Failed or failing PCM, but note that since is a rare event, the fault must be sought elsewhere before any control module is reprogrammed or replaced
What are the symptoms of code P0341?
Common symptoms of code P0341 could include one or more of the following-
- Stored trouble code and an illuminated warning light that may or may not flash
- Depending on the nature of the problem, multiple additional codes may be present along with P0341
- A no-start or hard-starting condition may be present, depending on the nature and severity of the problem
- If the engine starts and runs, severe misfires may be present at some or all engine speeds and loads
- If the engine starts and runs, the engine may run roughly at some or all engine speeds and loads, or the engine may stall unexpectedly or repeatedly at low engine speeds
- Depending on the nature of the problem, the idling quality may be poor, or the engine may not idle at all
- Varying degrees of power loss may be present
- Fuel consumption may increase dramatically
- The affected vehicle will usually not pass an emissions test
Help Us Help You
Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.
Reading P0341 on your car
A basic adapter will show you P0341, but not the ABS, airbag or transmission modules, and not the bidirectional tests that confirm which part has actually failed rather than which circuit reported it.
