Honda OBD/OBD2 Codes >> Odyssey 3.5L – Pilot 3.5L – Ridgeline 3.5L (2005 – 2009)

ModelYearEngine identificationSystem
Odyssey 3.5L2005-09J35A6/J35A7PGM-FI
Pilot 3.5L2005J35A6PGM-FI
Pilot 3.5L2006-08J35A9PGM-FI
Pilot 3.5L2006-08J35Z1PGM-FI
Pilot 3.5L2009J35Z4PGM-FI
Ridgeline 3.5L2006-08J35A9PGM-FI
Ridgeline 3.5L2009J35Z5PGM-FI

General information

  • Malfunction indicator lamp (MIL) will illuminate if certain faults are recorded.
  • ECM operates in backup mode if sensors fail, to enable vehicle to be driven to repair shop.

Accessing

  • Trouble codes can only be displayed by using a Scan Tool connected to the data link connector (DLC)
o Odyssey/Pilot 1
o Ridgeline 2

Erasing

  • Trouble codes can only be erased by using a Scan Tool connected to the data link connector (DLC).

Trouble code  identification

OBD-11 codeFault locationProbable cause
PO, P2,UORefer to OBD-11 trouble code tables
P1077Intake manifold air control actuator – high   RPM malfunctionWiring, intake manifold air control actuator, ECM programming, ECM
P1078Intake manifold air control actuator – low RPM   malfunctionWiring, intake manifold air control actuator, ECM programming, ECM
P1109Barometric pressure (BARO) sensor- range/performance problemBARO sensor, ECM programming, ECM
P1116Engine coolant temperature (ECT) sensor…:   range/performance problemWiring, ECT sensor, ECM programming, ECM
P1128Manifold absolute pressure (MAP) sensor- pressure lower than expectedMAP sensor
P1129Manifold absolute pressure (MAP) sensor – pressure higher than expectedMAP sensor
P1172Heated oxygen sensor (H02S) 1, bank 1 – circuit malfunctionWiring, H02S, ECM programming, ECM
P1174Heated oxygen sensor (H02S) 1, bank 2 – circuit malfunctionWiring, H02S, ECM programming, ECM
P1297Electrical load sensor – circuit/voltage lowWiring, underhood fuseboxlrelay plate, electrical load sensor, ECM programming, ECM
P1298Electrical load sensor – circuit/voltage highWiring, underhood fuseboxlrelay plate, electrical load sensor, ECM programming, ECM
P145CEvaporative emission (EVAP) canister purge system – incorrect flowWiring, hose leak/blockage, EVAP canister purge valve, mechanical fault, ECM programming, ECM
P1454Fuel tank pressure sensor- range/performance problemWiring, hose, fuel tank pressure sensor, fuel filler cap, EVAP canister/vent valve, ECM programming, ECM
P15ABEngine mounting control module – circuit/voltage lowWiring, engine mounting control module, ECM programming, ECM
P15ACEngine mounting control module – internal malfunctionWiring, engine mounting control module
P15ADEngine mounting control module – internal malfunctionWiring, engine mounting control module
P15AEEngine mounting control module – cylinder cut-out system – signal malfunctionWiring, engine mounting control module, ECM programming, ECM
P15AFEngine mounting control module – camshaft position (CMP) sensor – signal malfunctionWiring, CMP sensor, engine mounting control module, ECM programming, ECM
P15BOEngine mounting control module – crankshaft position (CKP) sensor – signal malfunctionWiring, CKP sensor, engine mounting control module, ECM programming, ECM
P15B1Engine mounting control module – crankshaft position (CKP) sensor/camshaft position (CMP) sensor – implausible signalWiring, CKP/CMP sensor, engine mounting control module, ECM programming, ECM
P1549Generator system – high voltageWiring, generator, ECM programming, ECM
P16COEngine control module (ECM) – incorrect programmingECM incorrectly programmed, ECM   programming, ECM
P16BBGenerator system – low voltageWiring, generator, ECM programming, ECM
P16BCGenerator system – low voltageWiring, generator, ECM programming, ECM
P16BDStarter motor relay 2 – malfunctionWiring, starter motor relay
P16BEStarter motor relay 1 – malfunctionWiring, starter motor relay
P16BFStarter motor relays 1/2- circuit malfunctionWiring, ECM programming, ECM
P16C4Engine mounting control relay – circuit malfunctionWiring, engine mounting control relay, engine mounting control module, ECM programming, ECM
P16C5Engine mounting control relay – circuit malfunctionWiring, engine mounting control relay, engine mounting control module, ECM programming, ECM
P16C6Engine mounting control solenoid – voltage high during self-testWiring, engine mounting control solenoid, engine mounting control module
P16C7Rear engine mounting control solenoid – circuit malfunctionWiring, engine mounting control solenoid, engine mounting control module
P16C8Front engine mounting control solenoid – circuit malfunctionWiring, engine mounting control solenoid, engine mounting control module
P16C9Engine mounting control module – internal malfunctionEngine mounting control module
P1658Electronic throttle system (ETS) relay – malfunctionWiring, ETS relay, ECM programming, ECM
P1659Electronic throttle system (ETS) relay – malfunctionWiring, ETS relay, ECM programming, ECM
P1683Throttle motor – default position spring performance problemWiring, throttle sticking/mechanically damaged, throttle motor
P1684Throttle motor – return spring performance problemWiring, throttle sticking/mechanically damaged, throttle motor
P1717Transmission range (TR) switch – open circuitWiring, transmission shift link adjustment, TR switch, ECM programming, ECM
P1743AT – gear shift malfunctionTransmission fluid, wiring, shift solenoid E, mechanical fault, ECM programming, ECM
P1744AT – gear shift malfunctionTransmission fluid, wiring, shift solenoid E, mechanical fault, ECM programming, ECM
P1745AT – gear shift malfunctionTransmission fluid, mechanical fault
P1780AT – gear shift malfunctionOther AT trouble codes stored, ECM   programming, ECM