Honda Accord Hybrid 3.0L – Civic Hybrid 1.3L – Insight 1.0L (2000 – 2009) OBD1 Codes

Model	Year	Engine identification	System
Accord Hybrid 3.0L	2005-07	JNA1	PGM-FI
Civic Hybrid 1.3L	2005-07	LDA1/2	PGM-FI
Insight 1.0L	2000-06	ECA1	PGM-FI

General information

Malfunction indicator lamp (MIL) will illuminate if certain faults are recorded.
ECM operates in backup mode if sensors fail, to enable vehicle to be driven to repair shop.

NOTE: The use of a Scan Tool is essential to obtain full diagnostic information.

Accessing

Trouble codes can only be displayed by using a Scan Tool connected to the data link connector (DLC).

o Accord 1
o Civic 2
o Insight 3

Erasing

Trouble codes can only be erased using a Scan Tool connected to the data link connector (DLC).

Trouble code identification

Flash code	OBD-11 code	Fault location	Probable cause
–	PO, P2, uo	Refer to OBD-11 trouble code tables	–
1	P1559	Motor commutation sensor A – circuit low input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
1	P1647	Power command signal circuit – low input	Wiring, motor control module (MCM), ECM
1	P16B3	Power command signaf circuit – low input	Wiring, motor control module (MCM), ECM
2	P1560	Motor commutation sensor A – circuit high input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
2	P1647	Power command signal circuit – high input	Wiring, motor control module (MCM), ECM
2	P16B4	Power command signal circuit – high input	Wiring, motor control module (MCM), ECM
3	P1561	Motor commutation sensor 8 – circuit low input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
3	P1647	Engine torque signal – circuit low input	Wiring, motor control module (MCM), ECM
3	P1685	Engine torque signal – circuit low input	Wiring, motor control module (MCM), ECM
4	P1562	Motor commutation sensor 8 – circuit high input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
4	P1647	Engine torque signal – circuit high input	Wiring, motor control module (MCM), ECM
4	P1686	Engine torque signal – circuit high input	Wiring, motor control module (MCM), ECM
5	P1128	Manifold absolute pressure (MAP) sensor – pressure lower than expected	MAP sensor
5	P1129	Manifold absolute pressure (MAP) sensor – pressure higher than expected	Wiring, vacuum leaks, MAP sensor
5	P1563	Motor commutation sensor C – circuit low input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
5	P1647	Mode signal circuit 1 – low input	Wiring, motor control module (MCM), ECM
5	P16B7	Mode signal circuit 1 – low input	Wiring, motor control module (MCM), ECM
6	P1564	Motor commutation sensor C – circuit high input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
6	P1647	Mode signal circuit 1 – high input	Wiring, motor control module (MCM), ECM
6	P16B8	Mode signal circuit 1 – high input	Wiring, motor control module (MCM), ECM
7	P1121	Throttle position (TP) sensor – position lower than expected	TP sensor
7	P1121 0	Throttle position (TP) sensor – signal lower than expected	Throttle body
7	P1122	Throttle position (TP) sensor – position higher than expected	TP sensor
7	P1122 0	Throttle position (TP) sensor – signal higher than expected	Throttle body
7	P1571	Motor commutation sensor – voltage input problem	Wiring, motor control module (MCM) programming, MCM
7	P1647	Mode signal circuit 2	Wiring, motor control module (MCM), ECM
7	P1689	Mode signal circuit 2	Wiring, motor control module (MCM), ECM
8	P1361	Camshaft position (CMP) sensor- intermittent signal	Wiring, CMP sensor, ECM programming, ECM
8	P1362	Camshaft position (CMP) sensor – no signal	Wiring, CMP sensor, ECM programming, ECM
8	P1577	High voltage detection signal – circuit problem	Wiring, motor control module (MCM), hybrid battery pack
10	P1576	Motor driver module – voltage signal circuit – low input	Wiring, motor control module (MCM), voltage converter module
10	P15A2	Motor driver module – voltage signal circuit – low input	Wiring, motor control module (MCM), voltage converter module
11	P1576	Motor driver module – voltage signal circuit – high input	Wiring, voltage converter module, motor power inverter module, motor control module (MCM)
11	P15A3	Motor driver module – voltage signal circuit – high input	Wiring, voltage converter module, motor power inverter module, motor control module (MCM)
12	P1491	Exhaust gas recirculation (EGR) system – valve lift insufficient	Wiring, EGR valve/position sensor, EGR solenoid, hose leak/blockage, ECM programming, ECM
12	P1491	Exhaust gas recirculation (EGR) valve – insufficient lift detected	Wiring, EGR valve, ECM programming, ECM
12	0		Wiring, EGR valve, ECM programming, ECM
12	P1498	Exhaust gas recirculation (EGR) valve position sensor – voltage high	Wiring, EGR valve/position sensor, ECM programming, ECM
12	P1498 D	Exhaust gas recirculation (EGR) valve position sensor – voltage high	Wiring, EGR valve, ECM programming, ECM
12	P1575	Motor power inverter module – voltage malfunction	Wiring, high voltage contactor, hybrid battery pack, motor control module (MCM) programming, MCM
12	P1575 g	Motor driver module – voltage malfunction	Wiring, hybrid battery pack, motor power inverter module, voltage converter module, battery condition monitor module, high voltage contactor control relay
12	P1576	Motor driver module – voltage malfunction	Wiring, hybrid battery pack, motor power inverter module, voltage converter module, battery condition monitor module, high voltage contactor control relay
13	P1106	Barometric pressure (BARO) sensor- range/performance problem	ECM programming, ECM
13	P1107	Barometric pressure (BARO) sensor- circuit/voltage low	ECM programming, ECM
13	P1108	Barometric pressure (BARO) sensor- circuit/voltage high	ECM programming, ECM
13	P1109	Barometric pressure (BARO) sensor- range/performance problem	BARO sensor, ECM programming, ECM
14	P1519	Idle air control (lAC) valve – circuit failure	Wiring, lAC valve, ECM programming, ECM
15	P1355	Intake side ignition coil – power supply circuit malfunction	Wiring, fuse, ignition coil, ECM programming, ECM
15	P1356	Exhaust side ignition coil – power supply circuit malfunction	Wiring, fuse, ignition coil, ECM programming, ECM
16	P1559	Motor commutation sensor A – circuit low input	Wiring, motor control module (MCM), motor commutation sensor, drive plate sensor
17	P1560	Motor commutation sensor A – circuit high input	Wiring, motor control module (MCM), motor commutation sensor, drive plate sensor
18	P1561	Motor commutation sensor B – circuit low input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
19	P1581	Motor power inverter module – current signal circuit low input	Wiring, motor control module (MCM) programming, MCM, hybrid battery pack
19	P1587	Motor power inverter module – current signal circuit low input	Wiring, motor control module (MCM) programming, MCM, motor power inverter module current sensor
19	P1587 g	Motor power inverter module – current signal circuit low input	Wiring, motor control module (MCM) programming, MCM, hybrid battery pack
20	P1297	Electrical load sensor – circuit/voltage low	Wiring, underhood fuseboxlrelay plate, electrical load sensor, ECM programming, ECM
20	P1298	Electrical load sensor – circuit/voltage high	Wiring, underhood fuseboxlrelay plate, electrical load sensor, ECM programming, ECM
20	P1581	Motor power inverter module – current signal circuit low input	Wiring, motor control module (MCM) programming, MCM, hybrid battery pack
20	P1588	Motor power inverter module – current signal circuit high input	Wiring, motor control module (MCM) programming, MCM, motor power inverter module current sensor
20	P1588 D	Motor power inverter module – current signal circuit low input	Wiring, motor control module (MCM) programming, MCM, hybrid battery pack
21	P1581	Motor power inverter module – current signal circuit problem	Wiring, motor power inverter module, hybrid battery pack, motor control module (MCM)
21	P1589	Motor power inverter module – current signal problem	Motor power inverter module current sensor, motor control module (MCM) programming, MCM, motor power inverter module, power drive unit capacitor
21	P1589 D	Motor power inverter module – current signal circuit problem	Wiring, motor power inverter module, hybrid battery pack, motor control module (MCM)
22	P1259	VTEC system malfunction	Wiring, VTEC solenoid/pressure switch, ECM programming, ECM
22	P1673	Motor control module (MCM) – relay stays activated	Wiring, MCM relay 1, MCM programming, MCM
23	P1586	Battery current – signal circuit problem	Wiring, battery current sensor, motor control module (MCM) programming, MCM
23	P1586 D	Motor power inverter module – current signal/battery current signal circuit problem	Wiring, battery condition monitor module, hybrid battery pack
24	P1582	Motor current U phase signal circuit – low input	Wiring, motor control module (MCM), motor current U phase sensor
24	P1590	Motor current U phase signal circuit – low input	Wiring, motor control module (MCM) programming, MCM, motor current U phase sensor
25	P1582	Motor current U phase signal circuit – high input	Wiring, motor control module (MCM), motor current U phase sensor
25	P1591	Motor current U phase signal circuit – high input	Wiring, motor control module (MCM) programming, MCM, motor current U phase sensor
26	P1583	Motor current V phase signal circuit – low input	Wiring, motor control module (MCM), motor current V phase sensor
26	P1592	Motor current V phase signal circuit – low input	Wiring, motor control module (MCM) programming, MCM, motor current
26	P1592	Motor current V phase signal circuit – low input	V phase sensor
27	P1583	Motor current V phase signal circuit – high input	Wiring, motor control module (MCM), motor current V phase sensor
27	P1593	Motor current V phase signal circuit – high input	Wiring, motor control module (MCM) programming, MCM, motor current V phase sensor
28	P1584	Motor current W phase signal circuit – low input	Wiring, motor control module (MCM), motor current W phase sensor
28	P1594	Motor current W phase signal circuit – low input	Wiring, motor control module (MCM) programming, MCM, motor current W phase sensor
29	P1584	Motor current W phase signal circuit – high input	Wiring, motor control module (MCM), motor current W phase sensor
29	P1595	Motor current W phase signal circuit – high input	Wiring, motor control module (MCM) programming, MCM, motor current W phase sensor
30	P1585	Motor current sensor – circuit malfunction	Wiring, UNIW phase motor current sensors, motor control module (MCM) programming, MCM
30	P1585 D	Motor current sensor – circuit malfunction	Wiring, UNIW phase motor current sensors
30	P1655	AT – signal failure	Communication wire, ECM programming, ECM
31	P16C3	DC-DC converter temperature sensor – circuit malfunction	Wiring, blocked hybrid battery pack cooling fan duct, hybrid battery pack cooling fan, DC-DC converter
32	P1572	Motor driver module – temperature signal circuit low	Wiring, voltage converter module, motor power inverter module, motor control module (MCM)
32	P15AO	Motor driver module – temperature signal circuit low	Wiring, voltage converter module, motor power inverter module, motor control module (MCM)
32	P1636	Motor power inverter module – internal circuit malfunction	Wiring, motor power inverter module
33	P1572	Motor driver module – temperature signal circuit high	Wiring, voltage converter module, motor power inverter module, motor control module (MCM)
33	P15A1	Motor driver module – temperature signal circuit high	Wiring, voltage converter module, motor power inverter module, motor control module (MCM)
36	P1573	DC-DC converter – temperature signal circuit problem	Wiring, DC-DC converter, motor control module (MCM) programming, MCM
36	P1646	Motor control module (MCM) – signal malfunction	Wiring, hybrid battery pack, ECM programming, ECM
37	P1573	DC-DC converter – temperature signal circuit high input	Wiring, motor control module (MCM), DC-DC converter
38	P1429	Motor driver module – overheating signal circuit problem	Wiring, motor control module (MCM), voltage converter module
38	P1438	Motor driver module – overheating	Wiring, voltage converter module, motor power inverter module, motor power inverter module fan, motor power inverter module fan duct line
38	P1429 D	Motor driver module – overheating signal circuit problem	Wiring, motor control module (MCM), voltage converter module
39	P1436	Motor power inverter module – overheating	Motor power inverter module, hybrid battery pack cooling fan duct, hybrid battery pack cover
39	P1438	Motor driver module – overheating	Wiring, motor power inverter module fan, motor power inverter module fan duct line, voltage converter module, motor power inverter module
40	P1430	Motor driver module – short circuit sensor malfunction	Wiring, motor control module (MCM), voltage converter module
40	P1439	Motor driver module – short circuit sensor malfunction	Wiring, motor control module (MCM), voltage converter module
40	P1658	Electronic throttle system (ETS) control relay – on malfunction	Wiring, ETS control relay, ECM programming, ECM
40	P1659	Electronic throttle system (ETS) control relay – off malfunction	Wiring, fuse, ETS control relay, underhood fusebox/relay plate, ECM programming, ECM
40	P1683	Throttle valve – return spring performance problem	Wiring, dirty throttle body, throttle body
40	P1684	Throttle valve – return spring performance problem	Wiring, dirty throttle body, throttle body
40	P16CO	ECM – programming error	ECM programming, ECM
41	P1166	Heated oxygen sensor (H02S)- front- heater circuit malfunction	Wiring, H025, ECM programming, ECM
41	P1166 0	Heated oxygen sensor (H02S) 1 – heater circuit malfunction	Wiring, fuses, H02S heater relay, ECM programming, ECM
41	P1167	Heated oxygen sensor (H02S)- front- heater circuit malfunction	Open circuit, wiring, H025, ECM programming, ECM
41	P1437	Motor power inverter module – short circuit	Wiring, motor power inverter module
41	P1437 0	Motor power inverter module – short circuit	Wiring, output busbar, motor stator, motor power cable, motor power inverter module, motor control module (MCM) programming, MCM
41	P1437 D	Motor driver module – short circuit	Wiring, motor power inverter module
41	P1439	Motor driver module – short circuit	Wiring, motor power inverter module
42	P1565	Motor commutation signal problem	Wiring, motor control module (MCM), motor commutation sensor, MCM
42	P1566	Motor commutation sensor -signal problem	Wiring, motor control module (MCM) programming, MCM
42	P1566 D	Motor commutation signal problem	Wiring, motor control module (MCM), commutation sensor, MCM
43	P1567	Cylinder position signal circuit problem	Wiring, motor control module (MCM) programming, MCM, ECM programming, ECM
43	P1647	Engine speed signal – circuit problem	Wiring, motor control module (MCM), ECM
45	P1434	Voltage converter module – high voltage	Code is stored when battery needs protection from very low temperature, system is OK
46	P1443	High voltage contactor/bypass contactor – contactor stays activated	Wiring, DC-DC converter, hybrid battery pack, motor power inverter module, motor control module (MCM) programming, MCM
47	P1634	Motor power inverter module – signal circuit malfunction	Wiring, motor power inverter module, motor control module (MCM) relay 2, fuse, MCM programming, MCM
48	P1157	Heated oxygen sensor (H02S) – front – circuit malfunction	Wiring, H02S, ECM programming, ECM
48	P1158	Heated oxygen sensor (H02S) – front- circuit low voltage negative terminal	Wiring, H02S, ECM programming, ECM
48	P1159	Heated oxygen sensor (H02S) – front – circuit low voltage positive terminal	Wiring, H02S, ECM programming, ECM
48	P1162	Heated oxygen sensor (H02S) – front – circuit malfunction	Wiring, H02S, ECM programming, ECM
48	P1168	Heated oxygen sensor (H02S) -front -low voltage	Wiring, short circuit, H02S, ECM programming, ECM
48	P1169	Heated oxygen sensor (H02S) -front – high voltage	Wiring, open circuit, H025, ECM programming, ECM
49	P1522	Brake booster pressure sensor – circuit malfunction, low voltage	Wiring, brake booster pressure sensor, brake booster vacuum line, ECM programming, ECM
49	P1523	Brake booster pressure sensor – circuit malfunction, high voltage	Wiring, brake booster pressure sensor, brake booster vacuum line, ECM programming, ECM
49	P1524	Brake booster pressure sensor – range/ performance problem	Wiring, brake booster pressure sensor, brake booster vacuum line, ECM programming, ECM
49	P1553	Hybrid battery pack temperature sensor 1 – signal circuit low input	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
50	P1554	Hybrid battery pack temperature sensor 1 – signal circuit high input	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
50	P1638	Motor control module (MCM) – internal circuit problem	MCM
51	P1555	Hybrid battery pack temperature sensor 2 – signal circuit low input	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
52	P1556	Hybrid battery pack temperature sensor 2 – signal circuit high input	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
52	P1562	Motor commutation sensor B – circuit high input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
53	P1557	Hybrid battery pack temperature sensor 3 – signal circuit lowinput	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
53	P1563	Motor commutation sensor C – circuit low input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
54	P1558	Hybrid battery pack temperature sensor 3 – signal circuit highinput	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
54	P1564	Motor commutation sensor C – circuit high input	Wiring, motor control module (MCM) programming, MCM, motor commutation sensor, drive plate sensor
55	P1571	Motor commutation sensor – voltage input problem	Wiring, motor control module (MCM) programming, MCM
55	P1633	Engine control module (ECM) circuit problem	Wiring, motor control module (MCM) programming, MCM
57	P1440	Motor power inverter module – output circuit malfunction	Wiring, motor power cable, motor stator, motor power inverter module, motor rotor, motor control module (MCM) programming, MCM
57	P1440 f)	Integrated motor assist system problem	Wiring, UNIW motor current phase sensors, motor power inverter module current sensor, motor control module (MCM) programming, MCM, motor power cable, drive sensor plate, motor stator
58	P1366	Camshaft position (CMP) sensor B/TDC sensor 2 – intermittent signal	Wiring, CMP sensor B, ECM programming, ECM
58	P1367	Camshaft position (CMP) sensor 8/TDC sensor 2 – no signal	Wiring, CMP sensor B, ECM programming, ECM
58	P1435	Charge/discharge balance problem	Low 12V battery, charging system malfunction, 12V battery
59	P1444	High voltage short circuit	Motor power inverter module, motor stator, motor power cable assembly, DC-DC converter, power drive unit capacitor, high voltage cable, motor power inverter module, hybrid battery pack, motorcontrol module (MCM) programming, MCM
59	P1444	High voltage short circuit	Wiring, motor power inverter module, voltage converter module, motor power cable, DC-DC converter, hybrid battery pack, motor control module (MCM)
59	D	High voltage short circuit
61	P1163	Heated oxygen sensor (H02S)- front- range/performanceproblem	H02S
61	P1163 D	Heated oxygen sensor (H02S) 1 – slow response	H02S 1
61	P1164	Heated oxygen sensor (H02S) – front – circuit/slow response	H02S
61	P1164 D	Heated oxygen sensor (H02S) – circuit range/performance problem	Wiring, H02S
61	P1165	Heated oxygen sensor (H02S) – front – range/performanceproblem	H02S
61	P1172	Heated oxygen sensor (H02S) – front – circuit malfunction	Wiring, H02S, ECM programming, ECM
61	P1172 D	Heated oxygen sensor (H02S) – circuit malfunction, out of range – high	Wiring, H02S
62	P1445	Bypass contactor malfunction	Wiring, hybrid battery pack, bypass resistor, DC-DC converter, motor power inverter module, bypass contactor, motor control module (MCM) programming, MCM
62	P1445 D	Bypass contactor problem	Wiring, motor control module (MCM), battery condition monitor module, hybrid battery pack, DC-DC converter, hybrid battery pack, MCM, battery condition monitor module, motor power inverter module, voltage converter module
63	P1448	Hybrid battery pack cooling – malfunction	Wiring, hybrid battery pack cooling fan, motor control module (MCM) programming, MCM
63	P1448 D	Hybrid battery pack – overheating	Hybrid battery pack, hybrid battery pack cooling fan, hybrid battery pack cooling fan duct
64	P1637	Motor control module (MCM) – internal circuit malfunction	MCM programming, MCM
64	P1648	Battery condition monitor module – communication signal circuit problem	Wiring, motor control module (MCM), battery condition monitor module
65	P1580	Battery current sensor – circuit malfunction	Wiring, battery current sensor, motor control module (MCM) programming, MCM
65	P1580 D	Battery current circuit problem	Wiring, battery condition monitor module, hybrid battery pack
66	P1568	Hybrid battery pack – individual voltage input problem	Wiring, battery condition monitor module, hybrid battery pack,
66	P1570	Hybrid battery pack – individual voltage problem	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
66	P1570 D	Hybrid battery pack – individual voltage input problem	Wiring, battery condition monitor module, hybrid battery pack,
67	P1568	Hybrid battery pack – temperature signal circuit malfunction	Wiring, hybrid battery pack, battery condition monitor module
68	P1574	Hybrid battery pack – temperature signal circuit malfunction	Wiring, hybrid battery pack
69	P1600	Integrated motor assist system malfunction	Other integrated motor assist codes stored
69	P1601	Integrated motor assist system malfunction	Other integrated motor assist codes stored
69	P1644	Motor control module (MCM) – signal malfunction	Wiring, hybrid battery pack, ECM programming, ECM
69	P1645	Motor control module (MCM) – signal malfunction	Wiring, hybrid battery pack, ECM programming, ECM
70	P1568	Battery cell – temperature signal circuit malfunction	Wiring, battery condition monitor module, hybrid battery pack
70	P1569	Battery cell – temperature signal circuit malfunction	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
70	P1569	Battery cell – low input	Wiring, battery condition monitor module, hybrid battery pack

	D
71	P1637	Motor control module (MCM) – internal circuit malfunction	motor control module (MCM) programming, MCM
71	P16BA	Battery cell – high input	Wiring, battery condition monitor module, hybrid battery pack
72	P1431	Hybrid battery pack – overheating	Hybrid battery pack
72	P1449	Hybrid battery pack – overheating	Hybrid battery pack
73	P1432	Battery cell – overheating	Hybrid battery pack
73	P1449	Battery cell – overheating	Hybrid battery pack
74	P1446	Hybrid battery pack – individual voltage input deviation	Wiring, hybrid battery pack, motor control module (MCM) programming, MCM
74	P1446 D	Hybrid battery pack – individual voltage input deviation	Wiring, hybrid battery pack, battery condition monitor module
74	P1449	Hybrid battery pack – individual voltage input deviation	Wiring, hybrid battery pack, battery condition monitor module
75	P1648	Motor control module (MCM) – communication signal circuit problem	Wiring, MCM, battery condition monitor module
76	P1638	Motor control module (MCM) – internal circuit malfunction	MCM programming, MCM
77	P1447	Hybrid battery pack deviation	Hybrid battery pack
78	P1433	Hybrid battery pack – deterioration	Hybrid battery pack
78	P1449	Hybrid battery pack – deterioration	Hybrid battery pack
79	P1629	Battery current sensor – circuit malfunction	Wiring, motor control module (MCM) programming, MCM
79	P1629 0	Motor control module (MCM) – internal circuit malfunction	MCM programming, MCM
79	P1635	Battery condition monitor module – malfunction	Wiring, battery condition monitor module
81	P15A4	AJC compressor driver – relay stays activated	Wiring, AJC compressor driver, motor power cable, A/C compressor
85	P15A5	Motor current sensor – circuit malfunction	Wiring, motor rotor calibration, UN/W phase motor current sensors, motor power inverter module, motor power cable, motor control module (MCM) programming, MCM
86	P1116	Engine coolant temperature (ECT) sensor – range/performance problem	Wiring, ECT sensor, IAT sensor, ECM programming, ECM
86	P15A6	U phase motor current sensor – circuit malfunction	Wiring, U phase motor current sensor, motor control module (MCM) programming, MCM
87	P15A7	V phase motor current sensor – circuit malfunction	Wiring, V phase motor current sensor, motor control module (MCM) programming, MCM
88	P15A8	W phase motor current sensor – circuit malfunction	Wiring, W phase motor current sensor, motor control module (MCM) programming, MCM
88	P1639	Motor control module (MCM) -signal circuit malfunction	Wiring, MCM, ECM programming, ECM
88	P1640	Motor torque signal circuit – low input	Wiring, hybrid battery pack, ECM programming, ECM
88	P1641	Motor torque signal circuit – high input	Wiring, hybrid battery pack, ECM programming, ECM
88	P1642	Battery signal circuit – low input	Wiring, hybrid battery pack, ECM programming, ECM
88	P1643	Battery signal circuit – high input	Wiring, hybrid battery pack, ECM programming, ECM
90	P1456	Evaporative emission (EVAP) canister purge system (fuel tank system) – leak detected	Hose, fuel tank/pressure sensor, fuel filler cap, EVAP valve/bypass solenoid, EVAP two way valve, EVAP canister/vent valve
90	P1456 D	Evaporative emission (EVAP) system – leakage	Fuel filler cap, EVAP canister purge valve, hoses, EVAP canister shut-off valve, ECM programming, ECM
90	P1457	Evaporative emission (EVAP) canister purge system (canister system)- leak detected	Hose, fuel tank/pressure sensor, EVAP valve/bypass solenoid, EVAP two way valve, EVAP canister/vent valve
90	P1457 D	Evaporative emission (EVAP) system – leakage	EVAP canister purge valve, EVAP two way valve/bypass solenoid, EVAP canister shut-off valve, 0-ring, hoses/lines, EVAP canister, ECM programming, ECM
91	P1454	Fuel tank pressure sensor – circuit range/performance	Wiring, blockage in EVAP canister/filter/vent hoses/drain joint or fuel tank pressure sensor air tube, EVAP canister vent shut-off valve, fuel tank pressure sensor
91	P16C1	Motor control module (MCM) – program not installed – motor control program	MCM programming, MCM
92	P16C1	Motor control module (MCM) – program not installed – battery condition monitor module program	MCM programming, MCM
93	P15AA	Motor rotor – position not learned	Wiring, motor rotor position sensor
94	P1541	Passenger compartment heater standby signal circuit – low input	Wiring, heater control panel, ECM programming, ECM
94	P1541 D	A/C control module – signal circuit – low voltage	Wiring, A/C control module, ECM programming, ECM
94	P1542	Passenger compartment heater standby signal circuit – high input	Wiring, heater control panel, ECM programming, ECM
94	P1542 D	A/C control module – signal circuit – high voltage	Wiring, ECM programming, ECM
105	P1420	NOx adsorptive catalyst system – efficiency below limit	NOx adsorptive three way catalyst
107	P16D7	ECM – CAN data bus – communication circuit malfunction	ECM programming, ECM
109	P1505	Intake system – leak detected	Vacuum leaks, PCV valve, EVAP canister purge valve, throttle body, intake manifold
110	P15B2	Brake fluid pressure sensor A – circuit low voltage	Wiring, brake fluid pressure sensor, ECM programming, ECM
110	P15B3	Brake fluid pressure sensor A – circuit range/performance problem	Wiring, brake fluid pressure sensor, ECM programming, ECM
110	P1584	Brake fluid pressure sensor B – circuit low voltage	Wiring, brake fluid pressure sensor, ECM programming, ECM
110	P1585	Brake fluid pressure sensor B – circuit range/performance problem	Wiring, brake fluid pressure sensor, ECM programming, ECM
110	P1586	Brake fluid pressure sensor AlB – circuit malfunction	Brake fluid pressure sensor(s), ECM programming, ECM
111	P1130	Heated oxygen sensor (H02S) 2/3 – faulty components	H025 2, H025 3
114	P1020	Valve position control circuit – valve stuck off	Oil level, wiring, VTEC solenoid valve assembly, oil pressure sensor – rocker arm, ECM programming, ECM
114	P1021	Valve position control circuit – valve stuck on	Oil level, wiring, VTEC solenoid valve assembly, oil pressure sensor – rocker arm
114	P1286	Oil pressure sensor, rocker arm – signal stuck low	Oil level, wiring, VTEC system oil line, oil pressure sensor – rocker arm
114	P1287	Oil pressure switch, rocker arm – circuit high voltage	Oil level, wiring, oil pressure switch – rocker arm, ECM programming, ECM
114	P1288	Oil pressure switch, rocker arm – circuit low voltage	Oil level, wiring, oil pressure switch – rocker arm, ECM programming, ECM
114	P1289	Oil pressure sensor, rocker arm – signal stuck high	Oil level, oil pressure sensor – rocker arm
114	P128A	Valve position control circuit – stuck off	Oil level, wiring, engine oil pressure sensor, rocker arm oil control valve
114	P128B	Valve position control circuit – malfunction	Oil level, wiring, oil pressure sensor- rocker arm, rocker arm oil control valve
115	P1024	Valve position control circuit – stuck on	Oil level, wiring, oil pressure sensor – rocker arm, rocker arm oil control valve
115	P1025	Valve position control circuit -valve sticking off	MAP sensor, rocker arm assembly
115	P1026	Valve position control circuit – valve stuck on	Rocker arm assembly
120	P1608	ECM – internal integrated motor assist controller area network – communication circuit malfunction	ECM programming, ECM
132	P1605	CAN data bus	ECM programming, ECM
132	P1606	Integrated motor assist controller area network malfunction	ECM programming, ECM
–	P1024	Valve position control circuit – valve sticking on	Wiring, rocker arm assembly
–	P1077	Intake manifold air control valve – stuck in high RPM position	Wiring, intake manifold air control actuator, intake manifold, ECM programming, ECM
–	P1078	Intake manifold air control valve – stuck in low RPM position	Wiring, intake manifold air control actuator, intake manifold, ECM programming, ECM
–	P1109	Barometric pressure (BARO) sensor – circuit malfunction, out of range	Wiring, ECM programming, ECM
–	P1116	Engine coolant temperature (ECT) sensor – range/performance problem	Wiring, ECT sensor 1, ECT sensor 2
–	P1128	MAP sensor – signal lower than expected	Wiring, MAP sensor
–	P1129	MAP sensor – signal higher than expected	Vacuum leaks, wiring, MAP sensor
–	P1157	Heated oxygen sensor (H02S) – H02S 1 – circuit malfunction	Wiring, H02S 1, ECM programming, ECM
–	P1172	Heated oxygen sensor (H02S) 1, bank 1 – out of range, high	Wiring, H02S
–	P1174	Heated oxygen sensor (H02S) 2, bank 2 – out of range, high	Wiring, H02S
–	P1286	Oil pressure sensor, rocker arm – signal stuck low	Oil level, wiring, VTEC system oil line, oil pressure sensor – rocker arm
–	P1287	Oil pressure switch, rocker arm – circuit high voltage	Oil level, wiring, oil pressure switch – rocker arm , ECM programming, ECM
–	P1288	Oil pressure switch, rocker arm -circuit low voltage	Oil level, wiring, oil pressure switch – rocker arm, ECM programming, ECM
–	P1289	Oil pressure sensor, rocker arm -stuck high	Oil level, oil pressure sensor – rocker arm
–	P1297	Electrical load detector – circuit low voltage	Wiring, electrical load detector, ECM programming, ECM
–	P1297	Electrical load detector – circuit low voltage	Wiring, underhood fuseboxlrelay plate, ECM programming, ECM
–	P1298	Electrical load detector – circuit high voltage	Wiring, fuse, electrical load detector, ECM programming, ECM
–	P1298	Electrical load detector – circuit high voltage	Wiring, underhood fuseboxlrelay plate, ECM programming, ECM
–	P128A	Valve position control circuit – valve stuck off	Oil level, wiring, engine oil pressure sensor, rocker arm oil control valve
–	P128B	Valve position control circuit – malfunction	Oil level, wiring, engine oil pressure sensor, rocker arm oil control valve
–	P15AB	Engine mounting control module – power supply circuit – low voltage	Wiring, engine mounting control module
–	P15AC	Engine mounting control module – internal circuit malfunction	Wiring, engine mounting control module
–	P15AD	Engine mounting control module – internal circuit malfunction	Wiring, engine mounting control module
–	P15AE	Cylinder pause signal malfunction	Wiring, engine mounting control module
–	P15AF	Camshaft position (CMP) sensor- signal malfunction	Wiring, engine mounting control module, ECM programming, ECM
–	P15BO	Crankshaft position (CKP) sensor – signal malfunction	Wiring, engine mounting control module, ECM programming, ECM
–	P15B1	Camshaft position (CMP) sensor/crankshaft position (CKP) sensor- signal correlation	Wiring, engine mounting control module, ECM programming, ECM
–	P1601	Integrated motor assist – system malfunction	Other integrated motor assist codes stored
–	P1607	Engine control module (ECM) – internal circuit failure	ECM programming, ECM
–	P1658	Electronic throttle system (ETS) control relay – on malfunction	Wiring, ETS control relay, ECM programming, ECM
–	P1659	Electronic throttle system (ETS) control relay – off malfunction	Wiring, fuse, ETS control relay, underhood fusebox/relay plate, ECM programming, ECM
–	P1683	Throttle valve – default position spring performance problem	Wiring, dirty throttle body, throttle body
–	P1684	Throttle valve – return spring performance problem	Wiring, dirty throttle body, throttle body
–	P16CO	ECM – programming error	ECM programming, ECM
–	P16C4	Engine mounting control actuator – engine mounting control power supply circuit – stuck off	Wiring, fuse, engine mounting control relay, engine mounting control module
–	P16C5	Engine mounting control actuator – engine mounting control power supply circuit – stuck on	Wiring, engine mounting control relay, engine mounting control module
–	P16C6	Engine mounting control actuator – high voltage during function test	Wiring, engine mounting control module, front, rear engine mountings
–	P16C7	Rear engine mounting actuator control circuit – control circuit high current	Wiring, engine mounting control module
–	P16C8	Front engine mounting actuator control circuit – control circuit high current	Wiring, engine mounting control module
–	P16C9	Engine mounting control module – internal circuit malfunction	Wiring, engine mounting control module
–	P16D5	CAN data bus	ECM programming, ECM
–	P16D6	Integrated motor assist controller area network malfunction	ECM programming, ECM