P1260 – Theft Detected – Vehicle Immobilized (Ford)
| Code | Fault Location | Probable Cause |
|---|---|---|
| P1260 | Theft Detected - Vehicle Immobilized (Buy Part On Amazon) |
We recommend Torque Pro
Table of Contents
- What Does Code P1260 Mean?
- Where is the P1260 sensor located?
- What are the common causes of code P1260?
- How expensive is it to fix code P1260?
- What are the symptoms of code P1260?
- What are common solutions to code P1260?
- How serious is code P1260?
- How do you troubleshoot code P1260?
- Get Help with P1260
What Does Code P1260 Mean?
OBD II fault code P1260 is a manufacturer-specific c code that is defined by carmaker Ford as P1260 – “Theft Detected Vehicle Immobilized”, or sometimes as P1260 – “Theft Detected (Vehicle Immobilized) Conditions” and is set when the PCM (Powertrain Control Module) detects a signal from the Passive Anti-Theft System (PATS) that a theft condition had occurred. Note that when a theft condition is detected, the PCM will disable the engine’s starting circuits and the fuel delivery system.
Starting the engine in a Ford Escape is a complicated process that begins with the PATS system checking and verifying that the correct ignition key is present. If the key passes this verification process, The PATS system will communicate this fact to the PCM, which will then enable the starting circuits and the fuel delivery system.
Provided the vehicle is “as built”, meaning that if the vehicle is in its original form with the same engine and transmission it left the factory with, this starting process is fairly reliable and trouble-free. However, some Ford Escape hybrid models, such as the 2005, 2006, 2008, and 2013 models are renowned for their unreliable transmissions, which can (among other things), cause the engine not to start.
As a practical matter, though, the engine and transmission control modules on Ford products are programmed together in the factory and for as long as the same engine and transmission are in the vehicles, the engine and transmission control modules will communicate with each other, and with several others correctly over a high-speed CAN (Controller Area Network) serial communication system. These communications include, but are not limited to communications with the PATS system, the instrument cluster, and the ABS control module/controller.
However, the operative words are “the same engine and transmission”, but given that the transmissions in the above-mentioned models are particularly prone to suffering catastrophic failures, the transmissions in these models are frequently replaced with used or rebuilt units. In practice, though, these units may or may not be free of the defects or issues that rendered the original transmissions useless or caused the engine not to start.
The problem with replacement transmissions is that although units from different models or build years may appear identical from the outside, not all Ford Escape transmissions use the a) same control software or b) the same version of the control software. The practical effect of installing a transmission that uses a different version of control software than the original transmission is that the engine control module will not recognize the replacement transmission because it cannot communicate with the replacement transmission.
There are more complications with a replacement transmission. Since the PCM (Powertrain Control Module), TCM (Transmission Control Module), ICCM (Instrument Cluster Control Module), and ABS Control Module all form integral parts of the PATS (Passive Anti-Theft) system, the PCM may sometimes misinterpret the lack of communication between itself and the transmission control unit as a theft condition, and it will set trouble code P1260 as a result.
See the “CAUSES” and “SOLUTIONS” sections for more details.
Where is the P1260 sensor located?
The image above shows the location of the transmission control module on a 2005 Ford Escape hybrid transmission, which is identical in all material respects to the 2006 Ford Escape hybrid. Note the electrical connectors at the bottom of the printed circuit board- these are the connectors and wiring that connect the transmission to the vehicle’s electrical system, which includes multiple control modules.
Note that the electrical connectors shown here will fit on many, if not most transmission control modules in Ford Escape hybrid models, so it’s easy to assume that any given replacement transmission is compatible with the PCM and other control modules.
What are the common causes of code P1260?
NOTE: In most instances of code P1260 on Ford Escape hybrids, the root cause(s) of the code involve issues with incorrect keys, damaged keys, incorrectly programmed keys, failed or defective PATS transceivers, abnormally low battery voltages, or even simple battery replacements.
However, since replacing the transmission on a FORD Escape hybrid is very unlikely to affect any of the above-mentioned parts/components, it is safe to assume that a no-start condition after a transmission replacement does not involve any of the above-mentioned parts/components. Therefore, the fault must be sought elsewhere before keys are reprogrammed or PATS receivers are replaced, although it can’t hurt to verify battery voltages and ground connections.
Nonetheless, some common causes of no-start conditions after a transmission replacement could include one or more of the following-
- Incompatible PCM and TCM software or software versions
- Defective, malfunctioning, or failed replacement transmission
- Damaged or disconnected wiring between the PCM and the transmission
- Failure to reset the safety cut-out switch on the HV battery pack to the “LOCK” position. Verify that the switch is not in the Service or Shipping positions; if it is, the HV battery is effectively switched off, and the engine will not start
Assuming that the replacement transmission is compatible with the PCM and other control modules, other possible causes of code P1260 could include one or more of the following-
- Corrupted software in either (or both) the PCM and instrument cluster
- Defective PATS control module
- Use of non-PATS-enabled ignition keys
- Use of damaged ignition smart keys
- Defects in the PCM power supply circuits and/or relay
- Shorted or interrupted VREF (reference voltage)
- Loss of power or ground in the PCM power supply circuit(s)
- Previous or unresolved theft condition
- Failed or failing PCM
- Failed or failing TCM
How expensive is it to fix code P1260?
As a general rule, replacing the transmission in a Ford Escape hybrid with a rebuilt transmission can (and very often does) run to between $3000 and about $5000, depending on the model and repair shop that performs the replacement.
Note, though, that this estimate may or may not include labor, diagnostic, and reprogramming charges, so we highly recommend that you consult several workshops with proven experience in diagnosing and replacing Ford Escape hybrid transmissions. This will ensure that you get price estimates that include all charges, including taxes, levies, and fees that apply in your location.
Note also that while it is possible to replace the transmission on Ford Escape hybrids on a DIY basis, the process requires extensive research to ensure that the replacement transmission is a) in good working order and b) compatible with the vehicle that will receive the replacement transmission.
What are the symptoms of code P1260?
Common symptoms of code P1260 could include one or more of the following-
- Stored trouble code and an illuminated anti-theft warning light
- In some cases, additional PATS-related trouble codes may be present along with P1260, with trouble code B1681- “PATS Receiver Module Signal Not Received” being common but note that cheap generic scan tools or code readers can typically not extract or display this code and its definition
- The engine will typically not crank
- In some cases of transmission replacements, the engine may start and run but will shut off again after about three seconds
What are common solutions to code P1260?
Some possible solutions to resolving code P1260 may include one or more of the following-
- Verify that all the control modules in the affected vehicle are operational and communicating over the CAN (Controller Area Network) serial communications systems that link them. Some modern high-end scan tools can a) display a diagram of all the control modules in the affected vehicle, and b) indicate control modules that are not communicating. However, be aware that non-Ford-specific equipment may not be able to extract fault codes from all non-communicating control modules
- Verify that the replacement transmission comes from a donor vehicle that was equipped with a PATS system. This is important because some pre-2006 Ford Escape models were not fitted with PATS systems, meaning that transmissions from non-PATS models will not work in any PATS-equipped Ford Escape vehicle
- Verify that the replacement transmission is compatible with the vehicle that will receive the replacement transmission. This includes verifying that the PCM and TCM (Transmission Control Module) are programmed with the same software version
- Verify that the software version in the TCM includes all the fixes, updates, and patches that are present in the PCM. Note that verifying this requires using Ford-specific diagnostic/programming equipment
- If the replacement transmission is compatible with the vehicle that will receive it, the replacement transmission must be reprogrammed with the operating parameters that apply to the affected vehicle to ensure it works as expected. Note that while some very high-en generic scan tools can perform this function, this process requires the use of Ford-specific software to get the best results
NOTE: We do not recommend that non-professional mechanics attempt the required programming procedures with non-Ford-specific equipment or software because of the very high likelihood that existing programming in related control modules may be erased or corrupted. Therefore, we recommend that you seek professional assistance with programming a replacement transmission on any Ford Escape model.
How serious is code P1260?
Since the presence of trouble code P1260 indicates a no-start condition, the question of how serious this code is does not really arise. However, as stated elsewhere, 2005, 2006, 2008, and 2013 Ford Escape models have notoriously unreliable transmissions, so we do not recommend that Escape models from these build years be driven or operated if there are any doubts about the operability of the transmissions in these models.
The fact is that the transmission in any Ford Escape model can fail catastrophically without any warning, and even more so in 2005, 2006, 2008, and 2013 model years that exhibit symptoms like harsh/erratic shifting, or emit whining, grinding, or rumbling mechanical noises. In such cases, code P1260 could be set at any time regardless of operating conditions, which means that if code P1260 is set the vehicle will typically be immobilized.
How do you troubleshoot code P1260?
Troubleshooting or diagnosing the eCVT transmissions in Ford Escape vehicles, including hybrid versions requires expert-level technical knowledge and experience, particularly in cases where a transmission replacement has caused trouble code P1260 to be set.
Moreover, diagnosing trouble code P1260 requires the use of a digital storage oscilloscope to test and verify the correct (or otherwise) operation of several serial communication networks, but note that interpreting waveforms correctly requires a level of technical knowledge that most non-professional mechanics do not possess.
WARNING: Based on the above, we do not recommend that non-professional mechanics attempt any diagnostic procedure(s) on the transmission that involves code P1260 on any Ford Escape model, particularly not on hybrid versions due to the high likelihood of suffering severe or even fatal electrocution by the high-voltage system. Be aware that the high-voltage system carries 330 volts, which is sufficient to cause severe burns and potentially fatal electrocution.
Help Us Help You
Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.
Reading P1260 on your car
P1260 is a manufacturer-specific code. Most inexpensive Bluetooth adapters read generic engine codes only and cannot reach these systems at all – reading it, and getting the manufacturer’s own description of the fault, needs a scanner that talks to the other modules.
