P1151 – Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2 (Ford)

By Bojan Popic (Contact Me)
Last Updated 2023-04-26
Master Mechanical Engineer
CodeFault LocationProbable Cause
P1151 Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2
(Buy Part On Amazon)
Wiring, intake/fuel system, H02S, EGR system, oil level, camshaft timing, cylinder compression, ECM

We recommend Torque Pro

Table of Contents

  1. What Does Code P1151 Mean?
  2. Where is the P1151 sensor located?
  3. What are the common causes of code P1151?
  4. Get Help with P1151

What Does Code P1151 Mean?

OBD II fault code P1151 is a manufacturer-specific code, defined by Ford as Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2. It is set when the PCM, based on the data from the upstream Oxygen sensor, concludes the cylinders on the Bank 2 side of the engine are running lean.

Illustration for trouble code P1151 - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2 (Ford)

The difference between this and standard lean-running codes is how it’s triggered. During every cycle, when the conditions are right, the PCM intentionally richens up the air-fuel mixture for a short period. Then, it monitors the signal from the O2 sensors and compares them against predetermined values. And if the one coming from the bank 2 sensor is out of range, the P1151 code is set. This is, in a way, an early-warning system, indicating a potential issue before it develops into something more serious. As such, the P1151 code usually won’t cause any driveability issues.

Be aware other carmakers also may use this code, with different definitions between different makes. This guide applies primarily to Ford vehicles.

Where is the P1151 sensor located?

The P1151 code is specific to F-150 trucks and Mustangs with 4.6 and 5.4 engines. However, it can also happen in vehicles with 4.0 V6 engines, including Rangers and Explorers.

All these vehicles have their engines mounted lengthways, with the Bank 2 on the driver’s side. So, this is where the oxygen sensor in question is located. And because it’s upstream, it will be somewhere between the exhaust manifold and catalytic converter. In most cases, the easiest way to access them is from underneath the vehicle. The photo below shows the upstream oxygen sensor’s location on a 2004 Ford F-150 with a 5.4 V8 engine.

Illustration for trouble code P1151 - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2 (Ford)

Another example is shown with this Ford Ranger with a V6 engine.

Illustration for trouble code P1151 - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2 (Ford)

What are the common causes of code P1151?

Several potential causes, which are specific to Bank 2, will trigger only the P1151 code.

Fouled upstream oxygen sensor
The oxygen sensor can get covered with carbon buildups and layers of unburnt particles, offsetting its readings. This is especially likely in high-mileage vehicles if these sensors were never replaced. While some results can be achieved by cleaning, replacing the sensor is the best solution.

Damaged Sensors’ wiring
Due to the location of the upstream sensors, its wiring is exposed to moisture, dirt, and road debris. This may cause corrosion inside the connector or damage the wires, which then offsets the sensor’s signal. A visual inspection can easily reveal any of the above.

Exhaust leak
An exhaust manifold or its gaskets may crack, creating an exhaust leak. This changes the composition of exhaust gases, which then may be registered as a lean mixture by the oxygen sensor. Traces of black soot on the exhaust pipes may reveal the leakage point.

Clogged fuel injector
One or more injectors on Bank 2 side are clogged, reducing the amount of fuel injected fuel and causing the engine to run lean.

In addition, several other issues could cause the whole engine to run lean during the test procedure. This could also trigger only the P1151 code or in combination with P1131, which is the same, but just for Bank 1.

MAF sensor
The readings from the MAF sensor are the basis on which the PCM adjusts the air-fuel mixture. And if the MAF’s hot wire is covered with dirt, its measurements will be incorrect. This potentially causes a running-lean condition. Cleaning the MAF sensor usually solves the problem.

Vacuum leaks
Any vacuum leak between the MAF and cylinder head will allow unmetered air into the intake, causing the mixture to become lean. This could be anything from cracked air ducts and broken EVAP hoses to intake manifold gaskets. Vehicles with 4.2-liter V6 engines are especially prone to this, and the repair is explained in Ford’s service bulletin TSB 05-22-6.

PCV system
A malfunctioning PCV system can have an effect similar to vacuum leaks. The usual things to look for are a wide-open PCV valve and cracked hoses connected to the cylinder head. In addition, a dipstick that doesn’t seal correctly may also cause these issues.

Help Us Help You

Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.

Reading P1151 on your car

P1151 is a manufacturer-specific code. Most inexpensive Bluetooth adapters read generic engine codes only and cannot reach these systems at all – reading it, and getting the manufacturer’s own description of the fault, needs a scanner that talks to the other modules.

Scanners that read all systems on Amazon