P0320 – Ignition/Distributor Engine Speed Input Circuit Malfunction (Ford)
| Code | Fault Location | Probable Cause |
|---|---|---|
| P0320 | Ignition/Distributor Engine Speed Input Circuit Malfunction (Buy Part On Amazon) | Wiring issues, Damaged reluctor ring, Missing Wiring Shields |
We recommend Torque Pro
Table of Contents
- What Does Code P0320 Mean?
- Where is the P0320 sensor located?
- What are the common causes of code P0320?
- Get Help with P0320
What Does Code P0320 Mean?
NOTE: While this guide is specific to Ford vehicles, P0320 is a generic OBD2 diagnostic code. If your vehicle is not a Ford, then please read the generic version of this guide as the following information will not apply to all vehicles. If you have Ford with this code, then we hope the below more detailed information helps you. Please comment below the article with your year, model, engine type, and mileage, and we will respond and try to help.
P0320 is a generic code trouble code defined as Ignition/Distributor Engine Speed Input Circuit Malfunction. This code is triggered when the ECM (Engine Control Module) receives incorrect signals from the sensors measuring the engine’s speed and the position of its internal components. This is used to adjust fuel injection and other running parameters for optimum performance. With the P0320 trouble code on, the engine will run poorly, stall, or even may not start at all.
The most common belief is that a faulty crankshaft position sensor causes this trouble code. Still, it doesn’t necessarily have to be so. Due to the complexity of modern engines, other sensors are also used for this task.
Where is the P0320 sensor located?
Most modern Ford gasoline engines have a variable valve timing, or VVT, which continuously changes the correlation between the crankshaft and camshafts. Depending on the conditions, this mechanism will open and close the valve earlier or later, which increases airflow. This is done to improve low-down torque while not sacrificing any top-end power. As a result, the driver doesn’t have to push the engine hard when accelerating, consequently improving fuel economy.
For optimum performance, the fuel and ignition must happen at an exact moment during the combustion process. Because the correlation between the crankshaft and camshafts is not constant, the ECM has to their positions at every moment. This is done by two separate sensors, with the crankshaft position sensor being one of them. While this component is usually fitted on the engine’s transmission side of the engine, in many Ford vehicles, it will be found on the timing belt side. The following photo shows the crankshaft position sensor’s location on a 2002 Ford F-150.
The other part of the equation is the camshaft position sensor, which determines the speed and position of the shaft whose name it bears. Due to the nature of the job, these sensors are always located near the camshafts. For most Ford models, camshaft position sensors are fitted on the cylinder head at the timing side of the engine. Engines with variable valve timing for the intake will have one sensor, while those with VVT on the exhaust, as well, will have two. The photo below shows its location in the 2014 Ford Taunus.
When the signal from either of these sensors is incorrect or missing, the ECM will trigger a P0320 trouble code. It may, in some cases, be accompanied by other crankshaft or camshaft-related codes. Moreover, the signals coming from these sensors can be implausible and seemingly make no sense. In such situations, the ECM may have difficulties determining which is faulty. This, again, may trigger the P0320 trouble code.
What are the common causes of code P0320?
General issues that may cause the P0320 trouble code range from malfunctioning sensors and broken wiring to, unlikely as it may be, defective ECM. These potential causes, though, are covered in detail in the generic article about the P0320 code on this site. Instead of going through them once more, we’ll focus on the issues specific to Ford and its vehicles.
Wiring issues
Broken wiring is a common cause for the P0320 code in trucks and truck-based SUVs (Explorer and Expedition) with 4.6 and 5.4-liter Modular engines. This happens because the harness that connects the crankshaft position sensor and the ECM is routed so that it may rub against the chassis or other components inside the engine bay. Checking the wiring for any signs of damage and repairing it by soldering will, in most cases, solve the problem.
Damaged reluctor ring
Engines with a crankshaft position sensor at the timing side have a reluctor ring, which sits behind the aux-belt pulley. Over time, dirt and corrosion buildups may form on its surface, offsetting the sensor’s readings. While cleaning such a reluctor ring is possible, replacing it with a brand new one is always a better and more reliable option.
Missing wiring shields
A batch of early 2014 Ford Focuses with 2.0-liter engines left the factory with incorrectly fitted wire shielding. As a result, the harness that connects to the crankshaft sensor, among other components, may rub against the intake manifold and get damaged. The repair procedure is described in Ford’s service bulleting 18-2062.
Help Us Help You
Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.
Reading P0320 on your car
A basic adapter will show you P0320, but not the ABS, airbag or transmission modules, and not the bidirectional tests that confirm which part has actually failed rather than which circuit reported it.

