P0113 – Intake Air Temperature Sensor Circuit High Input (Ford)
| Code | Fault Location | Probable Cause |
|---|---|---|
| P0113 | Intake Air Temperature Sensor Circuit High Input (Buy Part On Amazon) | MAF sensor, Wiring |
Where is the Intake air temperature sensor (IAT)? See our guide to the Intake air temperature sensor (IAT) – what it does, where it sits on the engine and how it fails.
We recommend Torque Pro
Table of Contents
- What Does Code P0113 Mean?
- Where is the P0113 sensor located?
- What are the common causes of code P0113?
- What are the symptoms of code P0113?
- Get Help with P0113
What Does Code P0113 Mean?
SPECIAL NOTES: Although generic OBD II trouble codes such as P0113 – “Intake Air Temperature Sensor 1 Circuit High Bank 1” can, and do affect all OBD II compliant vehicles, some vehicle makes and models are sometimes more susceptible to some generic trouble codes than most other vehicle makes and models under real-world driving and operating conditions. Therefore, this article will discuss generic trouble code P0113 as it applies to the Ford models that are most commonly affected by it. END OF SPECIAL NOTES.
OBD II fault code P0113 is a generic trouble code that is defined as, “Intake Air Temperature Sensor 1 Circuit High – Bank 1”, and is set when the PCM (Powertrain Control Module) detects an abnormal or unexpected voltage in the control and/or signal circuits of the Intake Air Temperature Sensor on Bank 1. Note that “Bank 1” refers to the bank of cylinders on V-type engines that contains cylinder #1.
Collectively, the various engine sensors that make modern gasoline engines work as well as they do, take account of dozens of environmental factors and conditions, all of which are critical to the efficient operation of modern gasoline engines. However, from an engine management perspective, some operating parameters are hugely variable, meaning that changes in some variable operating parameters can affect some control functions in meaningful ways unless the engine management system has a means of adapting some engine control functions to suit variable environmental factors.
We need not delve into the finer details of all possible interactions between all engine control functions here, but suffice to say that the volume of intake air that enters the engine is arguably the single most variable environmental factor that determines how well (or otherwise) an engine runs at any point in its operating range. Here is why-
All modern gasoline engines work best when the intake air and fuel are mixed in a ratio that is as close to stoichiometric as possible. Put differently, this means that the air/fuel mixture should ideally contain one part of fuel for every 14.7 parts of air because, in this ratio, all of the air will be used to combust all of the fuel.
However, it is not only very difficult to achieve stoichiometric fuel mixtures; it is also near impossible to maintain a stoichiometric air/fuel mixture for any length of time. This is because throttle inputs made during normal driving cause the injectors to inject more (or less) fuel, which either leans out or enriches the air/fuel mixture- depending on whether the throttle is opening or closing. Moreover, since the flow of the intake air is governed by the laws of physics, as opposed to a control module, the volume of the intake air that is available to the engine at any given moment is the basis upon which the PCM “builds” ignition timing and fuel delivery strategies.
Thus, the volume of the fuel that is injected at any given moment is subject to the volume of air that is available to the engine. However, the problem with atmospheric air is that its density, and hence, the amount of air that can be packed into any given unit of volume is hugely variable. For instance, cold air is denser than hot air, which means that more cold air can be “packed” into an engine’s cylinders than hot air. Similarly, atmospheric air at sea level is denser than air at high altitudes, which means that more air can be packed into an engine’s cylinders at sea level than at higher altitudes.
Thus, based on the variability of atmospheric air, engineers have developed engine sensors that take account of density variations in atmospheric air, these sensors being MAF (Mass Airflow) sensors, barometric pressure sensors, and intake air temperature sensors that, collectively, “weigh” the volume of air that enters the engine.
As a practical matter, MAF sensors measure the volume of air that flows into the engine, barometric pressure sensors measure the vehicle’s altitude above sea level, and intake air temperature sensors measure the actual temperature of the air that enters the engine. As with many other things automotive, the devil lives in the details, and in this case, the details involve the highly complex calculations the PCM performs using input data from the mentioned sensors. Below is the short version of how this calculation works-
As a first step, the PCM measures the total volume of air that flows over the MAF sensor, but at the same time, the PCM measures the temperature of the intake air using a dedicated Intake Air Temperature Sensor that is incorporated into the MAF sensor. Next, by comparing these measurements with input data from the Barometric Pressure Sensor, the PCM calculates the total volume of air that enters the engine as a function of its density, which is in its turn, a function of the ambient temperature and the vehicle’s altitude above sea level.
As a final step, and since fuel combusts more easily in a hot engine than in a cold engine, the PCM uses input data from one or more engine coolant temperature sensors to add or subtract fuel from the air/fuel mixture based on the engine’s temperature. This strategy prevents over fuelling when the engine is hot, and under fuelling when the engine is cold.
From the above, it should be clear that although intake air temperature sensors do not work in isolation, these sensors nevertheless fulfill a crucially important role in several critical engine control functions. Therefore, if any fault, defect, or malfunction occurs that affects the operation of the intake air temperature sensor, the PCM will recognize that it cannot control or manage the air/fuel mixture effectively. When tis happens, the PCM will set code P0113 and illuminate warning light as a result.
NOTE: In some cases, the PCM might revert to a default fuelling strategy that takes no account of variable environmental factors.
Where is the P0113 sensor located?
This image shows how the intake air temperature sensor is incorporated into the MAF sensor on a Ford Explorer. In this example, the red arrow indicates the MAF sensor’s sensing element, while the green arrow indicates the sensing element of the intake air temperature sensor. Note that if either sensor fails for whatever reason, both sensors must be replaced as an assembly since the sensors cannot be separated from each other.
Note that in cases where the intake air temperature sensor is not incorporated into the MAF sensor, the temperature sensor will typically be “plugged” into the inlet tract close to the air filter box between the MAF sensor and the air filter. It will also often be the only sensor in the intake ducting close to the air filter, which makes it easy to identify the temperature sensor correctly.
What are the common causes of code P0113?
Although code P0113 can potentially affect any Ford vehicle, intake air temperature sensor issues/failures are rarely the primary cause of engine management and/or fuel delivery issues on most Ford models. In fact, taken on their own, intake air temperature sensors on Ford vehicles are reasonably robust and reliable and, therefore, seldom fail on their own account.
However, intake air temperature sensors on Ford products are usually (but not always) incorporated* into the MAF sensor, which is frequently subjected to high volumes of oil mist and water vapor in the intake air that flows over their sensing elements. This is often the result of defective or malfunctioning PCV (Positive Crankcase Ventilation) valves or other issues in the larger engine vacuum system.
* Note that in cases where the intake air temperature sensor is not incorporated into the MAF sensor, the intake air temperature sensor’s sensing element will, like the MAF sensor’s element, be exposed directly to the airstream in the intake duct. Therefore, high volumes of oil mist and blowby gases in the intake tract will often affect both sensors in the same way.
As a practical matter, high volumes of oil mist in the inlet tract count among the most common causes of MAF sensor failures. This is because the oil mist does not only contaminate the MAF sensor’s sensing element, but also the intake air temperature sensor’s sensing element, thus rendering both sensors inaccurate at best and useless at worst. However, in some MAF sensor designs, the intake air temperature sensor’s sensing element is built into a protective cage, which can sometimes make it difficult to remove oil residues from the sensing element without damaging the sensor.
The above explains why code P0113 rarely appears in isolation on most Ford vehicles; in fact, in most instances of code P0113 on Ford vehicles, the code had set as the result of defects, malfunctions, or failures that do not involve failures of the air intake sensor itself.
It is perhaps worth mentioning at this point that changes in air temperature produce changes in the electrical resistance of the intake air temperature sensor’s sensing element, which produces changing signal voltages that the PCM interprets as changes in the ambient temperature.
Therefore, if a condition, such as a coating of oil mist on the sensor’s sensing element exists that prevents the intake air temperature sensor from measuring the ambient air temperature accurately, the sensor might generate an inaccurate or implausible signal voltage. In the absence of dedicated codes that indicate definitive electrical failures, the PCM will typically (but not always) interpret implausible ambient air temperature readings as failures and/or malfunctions of the intake air temperature sensor or its associated wiring.
Having said the above, other possible causes of code P0113 could include one or more of the following-
- The use of a substandard aftermarket MAF sensor
- Excessive mechanical wear of piston rings and/or cylinder walls that cause abnormally high volumes of blowby gases and oil mist to pass into the inlet tract through the PCV valve
- One or more defective or malfunctioning engine coolant temperature sensors
- Excessively high oil level
- Damaged, burnt, shorted, disconnected, or corroded wiring and/or electrical connectors in the intake air temperature sensor’s wiring
- The use of unsuitable or positively harmful solvents to remove oil residues from the MAF sensor’s sensing element
- Failed or defective intake air temperature sensor, but note that this is a relatively rare event
What are the symptoms of code P0113?
The most common symptoms of code P0113 are largely similar across all applications, and could include one or more of the following-
- Stored trouble code and an illuminated warning light
- Depending on the nature of the problem, multiple additional air/fuel metering codes may be present along with P0113, some of which might include both long and short-term fuel trim codes on the affected bank of cylinders
- Varying degrees of power loss may be present
- Fuel consumption may increase dramatically
- The engine may exhibit severe or random misfires at some engine speeds and loads
- The engine may stumble or hesitate upon acceleration
- The idling quality may be poor, but note that code P0113 will only very rarely cause the engine to stall or shut off unexpectedly
- One or more readiness monitors may not initiate or run to completion, in which case the vehicle will almost certainly not pass a mandatory emissions test
Help Us Help You
Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.
Reading P0113 on your car
A basic adapter will show you P0113, but not the ABS, airbag or transmission modules, and not the bidirectional tests that confirm which part has actually failed rather than which circuit reported it.
