P0300 – Random/multiple cylinder(s) -misfire detected (BMW)

Avatar photo
By Reinier (Contact Me)
Last Updated 2021-10-15
Automobile Repair Shop Owner
CodeFault LocationProbable Cause
P0300 Random/multiple cylinder(s) -misfire detected
(Buy Part On Amazon)
Spark plug(s), HT lead(s), injector(s), ignition coil(s), low compression, wiring

Where is the Ignition Coil? See our guide to the Ignition Coil – what it does, where it sits on the engine and how it fails.

We recommend Torque Pro

Table of Contents

  1. What Does Code P0300 Mean?
  2. Where is the P0300 sensor located?
  3. What are the common causes of code P0300?
  4. What are the symptoms of code P0300?
  5. Get Help with P0300

What Does Code P0300 Mean?

SPECIAL NOTES: Although generic OBD II trouble codes such as P0300 –”Random /multiple cylinders – misfire detected” can, and do affect all OBD II compliant vehicles, some vehicle makes and models are sometimes more susceptible to some generic trouble codes than most other vehicle makes and models. Under real-world driving and operating conditions, there are several reasons for some generic trouble codes to be more common on some vehicles than on others, but typical reasons include-

  • poor part/sensor/component design
  • poor routing of electrical wiring
  • poor placement of electrical components under seats, carpets, and center consoles
  • the exposed location of some parts/sensors/components on some vehicles
  • prolonged exposure to contaminants like road salt in some locations that cause damage to some parts and components on some vehicles, but not on others
  • difficulty in accessing some parts/sensors/components, thereby preventing or inhibiting the regular inspection, servicing, and/or replacement of affected parts/sensors/components during routine and/or scheduled servicing
  • Poor fuel quality in some locations

However, note that not all models of a particular vehicle make will necessarily be equally susceptible to one or more generic trouble codes, because car manufacturers often correct issues like poorly designed parts and/or poor routing of wiring at various points during a model’s production run. Nonetheless, this article will discuss generic trouble code P0300 –”Random /multiple cylinders – misfire detected” as it applies to the BMW models that are most commonly affected by it. END OF SPECIAL NOTES.

OBD II fault code P0300 is a generic trouble code that is defined as, P0300 –“Random /multiple cylinders – misfire detected”, and is set when the PCM (Powertrain Control Module) detects a series of random misfires that cannot be linked to any particular cylinder or cylinders. Note that on BMW vehicles, the PCM (Powertrain Control Module) is known as the DME (Digital Motor Electronics); despite the different name, the DME performs the same functions on BMW vehicles as the PCM does on other vehicle makes and models.

In theory, all modern engine management systems are designed and programmed to a) detect misfires, b), identify the cause of the misfire, and c), set one or more appropriate misfire trouble codes in one or more control modules when misfires occur. However, in practice, most misfire detection systems a) detect most misfires most of the time, b) identify the cause(s) of most misfires some of the time and, c) do not always set misfire codes for (various) reasons that are often, make and model specific.

Nonetheless, in a fully functional engine management system, the system acts as an emissions control system first, with diagnostic functions, including misfire detection, as a secondary consideration. Moreover, even in a fully functional engine management system, the mechanical wear of some rotating/moving components and a general loss of sensitivity of some engine sensors can sometimes combine to reduce the managements systems’ ability to detect some types of failures. Here is how it works in the case of misfire detection systems-

Since all misfires have the potential to affect exhaust emissions negatively, misfire detection systems are calibrated to detect misfires that may not be apparent to a casual observer. Put differently, this means that while a BMW engine may appear to be idling and/or running smoothly, one or more cylinders may not produce the same torque output as the other cylinders to an extent that would be visible or audible as a misfire.

However, since an engine management system cannot monitor the torque output of the cylinders directly, the engine management system, and by extension, the misfire detection system, monitors the rotational speed of the crankshaft- with the crankshaft’s rotational speed being a function of the combined, and equal, torque output of all the cylinders. This means that if all the cylinders produce the same torque output, the crankshaft would rotate at a constant rate at all engine speeds and loads.

In terms of operating principles, the misfire detection system uses the crankshaft position sensor and a reluctor wheel on the harmonic balancer (crankshaft pulley) to “count” the number of signals all the teeth on the reluctor wheel produce in one engine cycle, which is equal to two complete engine revolutions.

Although the frequency of the signals changes with the engine speed, the misfire detection looks for deviations in the frequency, with deviations being interpreted as misfires since reduced torque contributions from one or more cylinders exert momentary but measurable braking force(s)* on the crankshaft.

*Note that on most vehicle makes and models, the misfire detection system will only interpret deviations of 2 percent or more in the crankshaft’s speed as misfires to eliminate false positives that can occur as the result of naturally occurring deformations of the crankshaft.

In practice, these braking forces can have one of two patterns- cyclical or non-cyclical. In a cyclical pattern, the misfire is typically the result of, for instance, leaking engine valves, a defective ignition coil, or a defective fuel injector. There are other examples, but the point is that these kinds of defects produce predictable reductions in the torque output(s) of one or more cylinders at fixed points in every engine cycle.

Non-cyclical misfire patterns, on the other hand, are caused by random events such as engine vacuum leaks, whose effects typically (but not always) vary with changes in engine speed and/or engine load. In these kinds of situations, a gross vacuum leak can sometimes influence the flow of air through the intake manifold to the point where the airflow to one or more cylinders is severely disrupted.

In such cases, the disruption may affect different cylinders at different engine speeds and loads, thus creating random misfires that appear to “jump around” between cylinders, which the misfire detection system interprets as random misfires because it is unable to-

  • define a fixed misfire pattern
  • define a fixed misfire pattern at any given engine speed and load
  • associate the misfires with one or more particular cylinders relative to a fixed reference point in any given series of engine cycles

When this happens, the engine management system will recognize that it cannot perform its air and fuel metering functions effectively, and it will set a random misfire code and illuminate a warning light as a result, which begs the question of-

What causes code P0300 -“Random /multiple cylinders – misfire detected” on BMW vehicles?

It should be noted that while new or late model BMW models are not immune to this code, this code is far more prevalent on older BWM models than it is on newer models. Here is why-

In practice, the most common cause of this code involves engine vacuum leaks that disrupt the high engine vacuum that the PCV (Positive Crankcase Ventilation) system on all BMW models needs to prevent the build-up of combustion gases other waste products of the combustion process in the engine crankcase. Since the engine vacuum in BMW engines is much higher than on almost all other vehicle makes and models, BMW engines are sealed exceptionally tightly to prevent vacuum leaks.

However, over time, the rubber seals under oil filler caps, rubber plugs around oil dipsticks, valve cover gaskets, and vacuum lines/hoses begin to harden and degrade, thus causing degradation of the engine vacuum, which in turn, causes random misfires. Note, though, that while some vacuum leaks will only affect one or two cylinders, leaking oil filler caps and leaks in and around intake manifolds will almost invariably affect all cylinders, which will, in turn, cause random misfires.

Where is the P0300 sensor located?

Heavy carbon build-up inside an intake passage, arrowed

This image shows an example of a BMW oil filler cap. In this example, the red arrow indicates marginal damage caused by long use. While this type of damage to the rubber seal might seem insignificant, damage like this is the site of the vacuum leak that ultimately causes random misfires, more often than not.

Note that there is no reliable way to repair even marginally damaged oil filler cap seals; the only way to repair vacuum leaks like this is to replace the oil filler cap with an OEM part.

What are the common causes of code P0300?

The most common cause(s) of code P0300 on BMW vehicles are engine vacuum leaks, with common leak sites being-

  • Damaged, degraded, or cracked oil filler cap seals
  • Crushed, damaged, or degraded valve cover gaskets/seals
  • Damaged, perished, cracked, or dislodged vacuum lines and hoses
  • Crushed or damaged intake manifold gaskets and/or seals

Other possible causes of code P0300 could include-

  • One or more failed or defective control modules, including the DME (Digital Motor Electronics)
  • Defective fuel injectors
  • Defective ignition coils
  • Excessive fuel pressure
  • Insufficient fuel pressure

Note that while one or more of the issues listed immediately above can and do cause cylinder-specific misfires, these issues are exceedingly rare causes of code P0300 on BMW vehicles. Moreover, these issues will usually also be indicated by dedicated codes that relate directly to the cause, meaning that if code P0300 is present on a BMW vehicle, it will be accompanied by other codes.

What are the symptoms of code P0300?

more of the following-

  • Stored trouble code and an illuminated warning light
  • In some cases, multiple additional codes may be present along with P0300: codes relating to excessive fuel trim adaptations are common when P0300 is present
  • Varying degrees of power loss may be present
  • Fuel consumption may increase noticeably
  • The idling speed may be higher or lower than specified
  • The idling speed may fluctuate
  • The engine may stall at low engine speeds, such as when coming to a stop
  • The vehicle may surge and hesitate by turns: in severe cases, the alternate surging and hesitation may be severe: surging may also occur in patterns that may or may not be related to the engine speed and load
  • In some cases, gearshifts may be harsh, erratic, or unpredictable
  • The engine may backfire through the exhaust or the intake, depending on the nature of the problem

Help Us Help You

Please comment below describing your issue as well as the specifics of your vehicle (make, model, year, miles, and engine). A mechanic reads these, and other owners often recognise the symptoms straight away.

Reading P0300 on your car

A basic adapter will show you P0300, but not the ABS, airbag or transmission modules, and not the bidirectional tests that confirm which part has actually failed rather than which circuit reported it.

Scanners that read all systems on Amazon