Toyota Toyota 86-89 Cressida & Supra 86-92 3.0L Trouble Code Info

Toyota

Accessing – MIL

  • Switch ignition ON
  • Check MIL illuminates
  • Start engine.  Allow to idle.
  • If MIL extinguishes, no trouble codes have been recorded.
  • If MIL remains illuminated, access trouble codes.

Accessing – without Super monitor display

  • Switch ignition ON. Do NOT start engine
  • Cressida – jump DLC terminals T and E1 with a short lead 1
  • Supra – jump DLC terminals T and E1 with a short lead 2
  • First flashes of 0.5 second duration indicate ‘tens’, after a 1.5 second pause, next flashes of 0.5 second duration indicate ‘units’
  • A 2.5 second pause occurs between codes
  • After a 4.5 second pause, trouble codes will be repeated
  • The MIL flashes once every 0.25 seconds if the system is correct
  • Switch ignition OFF
  • Remove jump lead
Cressida Checking 86-89 Supra Checking Codes 86-92

Accessing -with Super monitor display

  • Switch ignition ON. Do NOT start engine.
  • Push and hold the SELECT and INPUT M keys simultaneously for 3 seconds minimum, DIAG should appear on the screen
  • Push and hold the SET key for 3 seconds minimum
  • The screen will show if the system is OK or if any trouble codes are recorded:
  • Cressida – 5
  • Supra – 6
  • A 3 second pause occurs between codes
  • After reading trouble codes either switch ignition OFF or press any key (except SET) to bring clock back
  • Switch ignition OFF
Cressida Super Monitor Supra Super Monitor

Clearing Trouble Codes

  • After the faults have been rectified, erase the trouble codes as follows:
  • Cressida – remove EFI fuse (15A) from underhood fusebox for 30 seconds minimum
  • Supra – remove EFI fuse (15A) from No.2 underhood fusebox for 30 seconds minimum
  • Reinstall fuse
  • Repeat accessing procedure to ensure no data remains in ECM fault memory

 Trouble Codes

86 – 88 Cressida 2.8L Engine Code: 5M-GE
89 Cressida 3.0L Engine Code: 7M-GE
86-92 Supra 3.0L Engine Code: 7M-GE
Trouble code Fault location Probable Cause
11 Engine control module (ECM) power supply Wiring, engine control relay, ECM
12 Engine speed (RPM) sensor -circuit Wiring, RPM sensor, ECM
13 Engine speed (RPM) sensor -above 1000 rpm Wiring, RPM sensor, ECM
14 Ignition reference signal -no signal Wiring, ignition module, ECM
21 Heated oxygen sensor (H02S) circuit front Wiring, H02S, ECM
22 Engine coolant temperature (ECT) sensor -circuit Wiring, ECT sensor, ECM
23 lntake air temperature (lAT) sensor-circuit Wiring, IAT sensor, ECM
24 lntake air temperature (lAT) sensor-circuit Wiring, IAT sensor, ECM
25 Mixture control- continuously lean Wiring, injector, H02S, ECT/VAF sensor, intake/fuel/ignition system, ECM
26 Mixture control -continuously rich Wiring, injector, fuel system, cold start injector, H02S, ECT/VAF sensor, ECM
27 Heated oxygen sensor (H02S) -rear circuit Wiring, H02S, ECM
31 Volume air flow (VAF) sensor-circuit Wiring, VAF sensor, ECM
32 Volume air flow (VAF) sensor-circuit Wiring, VAF sensor, ECM
41 Throttle position (TP) sensor -circuit Wiring, TP sensor, ECM
42 Vehicle speed sensor (VSS) -circuit Wiring, VSS, ECM
43 Starter signal -circuit Wiring, ignition switch, ECM
51 Switch signal -A/C switch ON during diagnosis Wiring, A/C switch, A/C amplifier, ECM
51 Switch signal -closed throttle position (CTP) switch OFF during diagnosis Wiring, CTP switch, ECM
51 Switch signal -park/neutral position (PNP) switch not in P or N during diagnosis Wiring, PNP switch, ECM
52 Knock sensor (KS) -circuit Wiring, KS, ECM
53 Knock control -malfunction ECM
71 Exhaust gas recirculation (EGR) system malfunction Hose leak/blockage, wiring, EGRT sensor, EGR solenoid, ECM